收藏 分享(赏)

ASTM_D_2166_-_D_2166M_-_13.pdf

上传人:益****师 文档编号:184138 上传时间:2023-03-04 格式:PDF 页数:7 大小:156.85KB
下载 相关 举报
ASTM_D_2166_-_D_2166M_-_13.pdf_第1页
第1页 / 共7页
ASTM_D_2166_-_D_2166M_-_13.pdf_第2页
第2页 / 共7页
ASTM_D_2166_-_D_2166M_-_13.pdf_第3页
第3页 / 共7页
ASTM_D_2166_-_D_2166M_-_13.pdf_第4页
第4页 / 共7页
ASTM_D_2166_-_D_2166M_-_13.pdf_第5页
第5页 / 共7页
ASTM_D_2166_-_D_2166M_-_13.pdf_第6页
第6页 / 共7页
亲,该文档总共7页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D2166/D2166M13Standard Test Method forUnconfined Compressive Strength of Cohesive Soil1This standard is issued under the fixed designation D2166/D2166M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revi

2、sion.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the determination of the uncon-fined compressive strength of cohesive soil in the intact,remolded,or recons

3、tituted condition,using strain-controlledapplication of the axial load.1.2 This test method provides an approximate value of thestrength of cohesive soils in terms of total stresses.1.3 This test method is applicable only to cohesive materialswhich will not expel or bleed water(water expelled from t

4、hesoil due to deformation or compaction)during the loadingportion of the test and which will retain intrinsic strength afterremoval of confining pressures,such as clays or cementedsoils.Dry and crumbly soils,fissured or varved materials,silts,peats,and sands cannot be tested with this method to obta

5、invalid unconfined compression strength values.NOTE1The determination of the unconsolidated,undrained strengthof cohesive soils with lateral confinement is covered by Test MethodD2850.1.4 This test method is not a substitute for Test MethodD2850.1.5 All observed and calculated values shall conform t

6、o theguidelines for significant digits and rounding established inPractice D6026,unless superseded by this standard.1.5.1 The procedures used to specify how data are collected/recorded and calculated in this test method are regarded as theindustry standard.In addition,they are representative of thes

7、ignificant digits that should generally be retained.The proce-dures used do not consider material variation,purpose forobtaining the data,special purpose studies,or any consider-ations for the users objectives;and it is common practice toincrease or reduce significant digits of reported data to com-

8、mensurate with these considerations.It is beyond the scope ofthis test method to consider significant digits used in analysismethods for engineering design.1.6 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be

9、 exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.6.1 The gravitational system of inch-pound units is usedwhen dealing with inch-pound units.In this system,the pound(lbf)represents a

10、unit of force(weight),while the unit for massis slugs.The rationalized slug unit is not given,unless dynamic(F=ma)calculations are involved.1.6.2 It is common practice in the engineering/constructionprofession to concurrently use pounds to represent both a unitof mass(lbm)and of force(lbf).This impl

11、icitly combines twoseparate systems of units;that is,the absolute system and thegravitational system.It is scientifically undesirable to combinethe use of two separate sets of inch-pound units within a singlestandard.As stated,this standard includes the gravitationalsystem of inch-pound units and do

12、es not use/present the slugunit for mass.However,the use of balances or scales recordingpounds of mass(lbm)or recording density in lbm/ft3shall notbe regarded as nonconformance with this standard.1.7 This standard does not purport to address all of thesafety problems,if any,associated with its use.I

13、t is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D653 Terminology Relating to Soil,Rock,and ContainedFluidsD854 Test Methods for

14、Specific Gravity of Soil Solids byWater PycnometerD1587 Practice for Thin-Walled Tube Sampling of Soils forGeotechnical PurposesD2216 Test Methods for Laboratory Determination of Water(Moisture)Content of Soil and Rock by MassD2488 Practice for Description and Identification of Soils(Visual-Manual P

15、rocedure)1This test method is under the jurisdiction ofASTM Committee D18 on Soil andRock and is the direct responsibility of Subcommittee D18.05 on Strength andCompressibility of Soils.Current edition approved May 15,2013.Published August 2013.Originallyapproved in 1963.Last previous edition approv

16、ed in 2006 as D2166 06.DOI:10.1520/D2166_D2166M-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D2850 Test Method for Unconsolidated-Und

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2