1、Designation:D1412/D1412M20Standard Test Method forEquilibrium Moisture of Coal at 96 to 97 Percent RelativeHumidity and 30 C1This standard is issued under the fixed designation D1412/D1412M;the number immediately following the designation indicates theyear of original adoption or,in the case of revi
2、sion,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers determination of the equilib-rium moisture of coal in an atmosphere over a satura
3、tedsolution of potassium sulfate at 30 C.NOTE1For information concerning the experimental work on whichthis test method is based,see(1-5).21.2 UnitsThe values stated in either SI units or non-SIunits are to be regarded separately as standard.The valuesstated in each system are not necessarily exact
4、equivalents;therefore,to ensure conformance with the standard,eachsystem shall be used independently of the other,and valuesfrom the two systems shall not be combined.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the
5、 user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established i
6、n the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D121 Terminology of Coal and CokeD388 Classification of Coals by RankD2013
7、Practice for Preparing Coal Samples for AnalysisD2234/D2234M Practice for Collection of a Gross Sampleof CoalD3172 Practice for Proximate Analysis of Coal and CokeD3173 Test Method for Moisture in the Analysis Sample ofCoal and CokeD3302 Test Method for Total Moisture in CoalD4239 Test Method for Su
8、lfur in the Analysis Sample ofCoal and Coke Using High-Temperature Tube FurnaceCombustionD4596 Practice for Collection of Channel Samples of Coalin a MineD5865 Test Method for Gross Calorific Value of Coal andCokeE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice
9、for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 ISO Standards:4ISO 5725-4 Accuracy(Trueness and Precision)of Measure-ment Methods and ResultsPart 4:Basic Methods for theDetermination of the Trueness of a Standard MeasurementMethodISO 5725-6 Accuracy(Trueness and
10、 Precision)of Measure-ment Methods and ResultsPart 6:Use in Practice ofAccuracy Values3.Significance and Use3.1 This test method affords a means of estimating theinherent moisture of either coal that is wet and shows visiblesurface moisture or coal that may have lost some moisture.Itmay be used for
11、estimating the surface,or extraneous moistureof wet coal,such moisture being the difference between thetotal moisture as determined by Test Method D3302 and theequilibrium moisture.3.2 When samples are collected in conformity with Classi-fication D388,the equilibrium moisture is considered to beequa
12、l to bed moisture with the exception of some low rankcoals that yield equilibrium moisture values below bed mois-ture.1This test method is under the jurisdiction of ASTM Committee D05 on Coaland Coke and is the direct responsibility of Subcommittee D05.21 on Methods ofAnalysis.Current edition approv
13、ed Sept.15,2020.Published September 2020.Originallyapproved in 1956.Last previous edition approved in 2019 as D1412/D1412M 19b.DOI:10.1520/D1412_D1412M-20.2The boldface numbers in parentheses refer to the list of references at the end ofthis standard.3For referenced ASTM standards,visit the ASTM web
14、site,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from International Organization for Standardization(ISO),ISOCentral Secretariat,BIBC II,Chemin de Blando
15、nnet 8,CP 401,1214 Vernier,Geneva,Switzerland,http:/www.iso.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with in
16、ternationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.3.3 The results obtained by this test method are sensitive tomany influences,and therefore,raw(uncorrected)equilibriummoisture data may be of limited value in and of themselves.When working with low rank coals,the results yielded by thistest method
