1、Designation:D1552161Standard Test Method forSulfur in Petroleum Products by High TemperatureCombustion and Infrared(IR)Detection or ThermalConductivity Detection(TCD)1This standard is issued under the fixed designation D1552;the number immediately following the designation indicates the year oforigi
2、nal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defen
3、se.1NOTEThe title was corrected editorially in February 2017.1.Scope*1.1 This test method covers procedures for the determina-tion of total sulfur in petroleum products including lubricatingoils containing additives,and in additive concentrates.This testmethod is applicable to samples boiling above
4、177 C(350 F)and containing a mass fraction of sulfur between 0.22%and24.2%.Other sulfur concentrations may be analyzed,but theprecision stated may or may not apply.These procedures useIR detection or TCD following combustion in a furnace.1.2 Petroleum coke containing a mass fraction of sulfurbetween
5、 2.53%to 3.79%sulfur may be analyzed.Other sulfurconcentrations may be analyzed,but the precision stated mayor may not apply.NOTE1The D155208(2014)version of this standard contained twoother procedures using iodate titrations.Since these procedures are nolonger being used in the industry laboratorie
6、s based on a survey ofD02.SC 3 laboratories conducted in September 2014,they are beingdeleted.For earlier information on the deleted procedures,D155208(2014)may be perused.1.3The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.4 T
7、his standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2
8、.1 ASTM Standards:2D4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD6299 Practice for Applying Statistical Quality Assuranceand Control Charting Techniques to Evaluate AnalyticalMeasurement System Performanc
9、eD6300 Practice for Determination of Precision and BiasData for Use in Test Methods for Petroleum Products andLubricantsD6792 Practice for Quality System in Petroleum Productsand Lubricants Testing Laboratories3.Summary of Test Method3.1 The sample is weighed and placed into a furnace havingan oxyge
10、n atmosphere sufficient to combust the entire sampleand a temperature between 1150 C and 1450 C for ProcedureA or 1150 C for Procedure B.Most sulfur present is com-busted to SO2,which is then measured with a detector aftermoisture and dust are removed by traps.The instrumentcalculates the mass perce
11、nt sulfur from the sample mass,theintegrated detector signal,and a predetermined calibrationfactor.The calibration factor is determined using standardsapproximating the material to be analyzed.3.1.1 Procedure AAfter combustion of the sample andsubsequent moisture/dust removal,SO2is measured usinginf
12、rared(IR)detection.3.1.2 Procedure BAfter combustion of the sample andsubsequent moisture/dust removal,SO2is measured using1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.03 on Elem
13、ental Analysis.Current edition approved July 1,2016.Published August 2016.Originallyapproved in 1958.Last previous edition approved in 2015 as D1552 15.DOI:10.1520/D1552-16E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For An
14、nual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis internationa
15、l standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 t
16、hermal conductivity detection.An apparatus utilizing TCDmay require the sample gas to pass an oxygen scrubber andadsorption/desorption traps to allow passing of contaminantsprior to measuring SO2.4.Significance and Use4.1 This test method provides a means of monitoring thesulfur level of various petroleum products and additives.Thisknowledge can be used to predict performance,handling,orprocessing properties.In some cases the presence of sulfurcompounds is beneficial to the product and monitorin
