1、Designation:D100010Standard Test Methods forPressure-Sensitive Adhesive-Coated Tapes Used forElectrical and Electronic Applications1This standard is issued under the fixed designation D1000;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revi
2、sion,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 These test methods c
3、over procedures for testingpressure-sensitive adhesive-coated tapes to be used as electri-cal insulation.These tapes are classified as follows:1.1.1 Class 1Non-elastomeric backings made from mate-rials such as:Paper,flat or creped,Fabric,uncoated or coated,Cellulose ester films,Polyethylene terephth
4、alate(polyester)films,Fluorocarbon polymer films,Composite filament films,Polyamide films,Polyimide films,andCombinations thereof.1.1.2 Class 2Elastomeric backings that are characterizedby both high stretch and substantial recovery.These backingsare made from materials such as:Vinyl chloride and co-
5、polymers,Vinylidene chloride and co-polymers,andPolyethylene and co-polymers.1.2 Test laminates of Class 1 and Class 2 backings accord-ing to Class 1 test methods.1.3 The procedures appear in the sections indicated belowand in alphabetical order:Adhesion Strength to Steel and Backing at Room Tempera
6、ture46 53Adhesion Strength to Steel and Backing at Low Temperatures46 53Bond Strength After Solvent Immersion110 115Breaking Strength and Elongation at Room Temperature37 45Breaking Strength and Elongation at Low Temperatures37 45Conditioning6 8Curling and Twisting140 146Dielectric Breakdown Voltage
7、83 90Effect of Accelerated Aging on High-Temperature Tapes97 103Flagging66 76Flammability104 109Hazards/Precautions3Insulation Resistance at High Humidity91 96Length of Tape in a Roll28 36Oil Resistance116 122Puncture Resistance123 128Resistance to Accelerated Aging(Heat and Moisture)129 139Sampling
8、4Specimen Preparation5Thermosetting Properties77 82Thickness21 27Unwind Force at Room Temperature54 65Unwind Force at Low Temperatures54 65Width11 20NOTE1These procedures apply to both Class 1 and Class 2 tapesexcept as noted above.1.4 This is a firetest response standard.1.5 The values stated in SI
9、 units are the standard,unlessotherwise noted.If a value for measurement is followed by avalue in inch-pound or English units in parentheses,the secondvalue may only be approximate and is for information only.The first stated value is the preferred unit.NOTE2These test methods are similar to IEC 604
10、543,but may differsometimes in some details.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory
11、 limitations prior to use.For specific hazardssee Section 3.2.Referenced Documents2.1 ASTM Standards:2A167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate,Sheet,and Strip(With-drawn 2014)3D149 Test Method for Dielectric Breakdown Voltage andDielectric Strength of Solid Elec
12、trical Insulating Materialsat Commercial Power Frequencies1These test methods are under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and are the direct responsibility ofSubcommittee D09.07 on Flexible and Rigid Insulating Materials.Current edition approved
13、Jan.1,2010.Published February 2010.Originallyapproved in 1948.Last previous edition approved in 2009 as D100009.DOI:10.1520/D1000-10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informati
14、on,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA
15、19428-2959.United States1 D257 Test Methods for DC Resistance or Conductance ofInsulating MaterialsD295 Test Methods for Varnished Cotton Fabrics Used forElectrical InsulationD374 Test Methods for Thickness of Solid Electrical Insu-lation(Withdrawn 2013)3D1711 Terminology Relating to Electrical Insu
16、lationD3487 Specification for Mineral Insulating Oil Used inElectrical ApparatusD5032 Practice for Maintaining Constant Relative Humidityby Means of Aqueous Glycerin SolutionsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 IEC Standard:IEC 60454-3 Specification for Pressure-Sensitive AdhesiveTapes for Electrical Purposes43.Hazards3.1 The following specific substances are flammable liq-uids.Do not use them in the vicinity of open flames orelectr
