收藏 分享(赏)

ASTM_C_1565_-_09.pdf

上传人:益****师 文档编号:184822 上传时间:2023-03-04 格式:PDF 页数:5 大小:100.03KB
下载 相关 举报
ASTM_C_1565_-_09.pdf_第1页
第1页 / 共5页
ASTM_C_1565_-_09.pdf_第2页
第2页 / 共5页
ASTM_C_1565_-_09.pdf_第3页
第3页 / 共5页
ASTM_C_1565_-_09.pdf_第4页
第4页 / 共5页
ASTM_C_1565_-_09.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:C156509Standard Test Method forDetermination of Pack-Set Index of Portland Cement1This standard is issued under the fixed designation C1565;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numbe

2、r in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the determination of the pack-set index,which provides an indication of the mechanical forceneeded to overcome the cons

3、olidation of portland cement.1.2 The pack-set index number provides a numerical valueuseful for manufacturers who desire to measure and control theeffect that vibration-induced consolidation has upon the manu-factured cement.1.3 The values stated in SI units are to be regarded asstandard.No other un

4、its of measurement are included in thisstandard.Values stated in SI units shall be obtained bymeasurement in SI units or by appropriate conversion,usingthe rules of Conversion and rounding given in StandardIEEE/ASTM SI 10,of measurements made in other units.1.4 This standard does not purport to addr

5、ess all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.(WARNINGFresh hydraulic-cementitious mixtures are caustic an

6、d maycause chemical burns to skin and tissue upon prolongedexposure.)22.Referenced Documents2.1 ASTM Standards:3C1005 Specification for Reference Masses and Devices forDetermining Mass and Volume for Use in the PhysicalTesting of Hydraulic CementsIEEE/ASTM SI 10 International System of Units(SI)TheM

7、odernized Metric System3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 pack set,na condition of hydraulic cement,exhib-ited in varying degrees,following silo storage or transport inbulk railcars or trucks,that causes the cement to resist flowinguntil considerable mechanical eff

8、ort has been applied.3.1.2 pack-set index,nthe numerical indication of thedegree of pack set a particular cement exhibits when subjectedto the procedures of this test method.3.1.3 peak voltage,n as pertaining to this method only,the energy in volts applied to consolidate the sample,whichresults in t

9、he maximum pack-set index for a particular cementand the apparatus used for the measurement.4.Summary of Test Method4.1 Portland cement is placed into a flask and then consoli-dated on a vibrating table by a vibration force controlled bytime and volts.The consolidated bed is measured for relativestr

10、ength by turning the flask to a horizontal position androtating in 180 increments until the bed collapses from thebottom of the flask.The number of half turns is a relativeindication of the force required to overcome the consolidationand is designated the pack-set index,or P.S.I.5.Significance and U

11、se5.1 This method is intended to help manufacturers deter-mine the relative pack-set tendency of their cement(s).The testestablishes a pack-set index which,when properly correlatedwith field performance,is useful in predicting or preventingfield unloading difficulties.5.2 The test is an aid to routi

12、ne control during cementproduction and is not suitable for specification purposes.5.3 In general,field performance of cement flowability issatisfactory when the pack-set index as determined on freshlyground cement averages 0 to 15 and is unsatisfactory when theindex exceeds 25.Any prediction of fiel

13、d performance ofcement flowability measuring 16 to 25 is tenable.These aregeneral ranges and the field performance of individual cementsmay not necessarily fall within these ranges.Additionalconditions,after the cement has left the control of the manu-facturing facility,can affect the apparent pack

14、set index as well.5.4 Any attempt to apply the critical range of pack-set indexnumbers based on freshly ground cement to job cement withoutspecial treatment of the sample would be problematic.The test1This test method is under the jurisdiction of ASTM Committee C01 on Cementand is the direct respons

15、ibility of Subcommittee C01.20 on Additions.Current edition approved June 1,2009.Published July 2009.Originally approvedin 2003.Last previous edition approved in 2004 as C1565 04.DOI:10.1520/C1565-09.2Section on Safety,Manual of Cement Testing,Annual Book of ASTMStandards,Vol 04.01.3For referenced A

16、STM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 is a“GO-NO GO”type of test and should not be used forspecification purposes.5.5 The pack-set index of field

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2