1、Designation:C170918Standard Guide forEvaluation of Alternative Supplementary CementitiousMaterials(ASCM)for Use in Concrete1This standard is issued under the fixed designation C1709;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、 year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This Guide is intended to provide a technical approachto the evaluation of alternative supplementary cementitious
3、materials such as pozzolans and hydraulic materials that falloutside the scope of Specifications C618,C989,and C1240.This Guide provides the initial steps for a comprehensiveevaluation of an ASCM that provides due diligence for itsspecific intended uses in concrete;however,it does notevaluate confor
4、mance to all possible performance criteria forall types of concrete mixtures.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 Performing the tests or meeting the test limits in thisguide should not imply that the material
5、tested meets therequirements of Specifications C618,C989,and C1240.Thesematerials should not be represented as such and each specificsource is to be evaluated separately.1.4 This guide does not purport to address all environmen-tal and safety concerns,if any,associated with its use.It is theresponsi
6、bility of the user of this guide to establish the appro-priate environmental,health,and safety issues,and identifyappropriate risk management procedures.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Deci
7、sion on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C39/C39M Test Method for Compressive Strength of Cylin-drical Concrete SpecimensC78 T
8、est Method for Flexural Strength of Concrete(UsingSimple Beam with Third-Point Loading)C109/C109M Test Method for Compressive Strength ofHydraulic Cement Mortars(Using 2-in.or 50-mm CubeSpecimens)C114 Test Methods for Chemical Analysis of HydraulicCementC125 Terminology Relating to Concrete and Conc
9、rete Ag-gregatesC138/C138M Test Method for Density(Unit Weight),Yield,and Air Content(Gravimetric)of ConcreteC143/C143M Test Method for Slump of Hydraulic-CementConcreteC157/C157M Test Method for Length Change of HardenedHydraulic-Cement Mortar and ConcreteC186 Test Method for Heat of Hydration of H
10、ydraulicCementC204 Test Methods for Fineness of Hydraulic Cement byAir-Permeability ApparatusC231/C231M Test Method forAir Content of Freshly MixedConcrete by the Pressure MethodC232/C232M Test Method for Bleeding of ConcreteC311 Test Methods for Sampling and Testing Fly Ash orNatural Pozzolans for
11、Use in Portland-Cement ConcreteC403/C403M Test Method for Time of Setting of ConcreteMixtures by Penetration ResistanceC430 Test Method for Fineness of Hydraulic Cement by the45-m(No.325)SieveC457/C457M Test Method for Microscopical Determinationof Parameters of the Air-Void System in Hardened Con-c
12、reteC469 Test Method for Static Modulus of Elasticity andPoissons Ratio of Concrete in Compression1This guide is under the jurisdiction of ASTM Committee C09 on Concrete andConcrete Aggregates and is the direct responsibility of Subcommittee C09.24 onSupplementary Cementitious Materials.Current edit
13、ion approved March 1,2018.Published April 2018.Originallyapproved in 2011.Last previous edition approved in 2011 as C170911.DOI:10.1520/C1709-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volu
14、me information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in acc
15、ordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 C618 Specification for Coal Fly
16、Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteC666/C666M Test Method for Resistance of Concrete toRapid Freezing and ThawingC672/C672M Test Method for Scaling Resistance of Con-crete Surfaces Exposed to Deicing ChemicalsC989 Specification for Slag Cement for Use in Concrete andMortarsC1012/C1012M Test Method for Length Change ofHydraulic-Cement Mortars Exposed to a Sulfate SolutionC1064/C1064M Test Method for Temperature of FreshlyMixed Hydraulic-Cement ConcreteC1202 Test Method for
