收藏 分享(赏)

ASTM_C_1130_-_17.pdf

上传人:益****师 文档编号:185106 上传时间:2023-03-04 格式:PDF 页数:9 大小:355.16KB
下载 相关 举报
ASTM_C_1130_-_17.pdf_第1页
第1页 / 共9页
ASTM_C_1130_-_17.pdf_第2页
第2页 / 共9页
ASTM_C_1130_-_17.pdf_第3页
第3页 / 共9页
ASTM_C_1130_-_17.pdf_第4页
第4页 / 共9页
ASTM_C_1130_-_17.pdf_第5页
第5页 / 共9页
ASTM_C_1130_-_17.pdf_第6页
第6页 / 共9页
亲,该文档总共9页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:C113017Standard Practice forCalibration of Thin Heat Flux Transducers1This standard is issued under the fixed designation C1130;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenth

2、eses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice,in conjunction with either Test MethodC177,C518,C1114,or C1363,establishes procedures for thecalibration of heat flux transducers that are dim

3、ensionally thinin comparison to their planar dimensions.1.1.1 The thickness of the heat flux transducer shall be lessthan 30%of the narrowest planar dimension of the heat fluxtransducer.1.2 This practice describes techniques for determining thesensitivity,S,of a heat flux transducer when subjected t

4、o onedimensional heat flow normal to the planar surface or wheninstalled in a building application.1.3 This practice shall be used in conjunction with PracticeC1046 and Practice C1155 when performing in-situ measure-ments of heat flux on opaque building components.Thispractice is comparable,but not

5、identical,to the calibrationtechniques described in ISO 9869-1.1.4 This practice is not intended to determine the sensitivityof heat flux transducers used as components of heat flow meterapparatus,as in Test Method C518,or used for in-situindustrial applications,as covered in Practice C1041.1.5 The

6、text of this standard references notes and footnoteswhich provide explanatory material.These notes and footnotes(excluding those in tables and figures)shall not be consideredas requirements of the standard.1.6 UnitsThe values stated in SI units are to be regardedas standard.The values given in paren

7、theses are provided forinformation only and are not considered standard.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and

8、deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-men

9、dations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C168 Terminology Relating to Thermal InsulationC177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarded-Hot-Pl

10、ate ApparatusC518 Test Method for Steady-State Thermal TransmissionProperties by Means of the Heat Flow Meter ApparatusC1041 Practice for In-Situ Measurements of Heat Flux inIndustrial Thermal Insulation Using Heat Flux Transduc-ersC1044 Practice for Using a Guarded-Hot-Plate Apparatus orThin-Heater

11、 Apparatus in the Single-Sided ModeC1046 Practice for In-Situ Measurement of Heat Flux andTemperature on Building Envelope ComponentsC1114 Test Method for Steady-State Thermal TransmissionProperties by Means of the Thin-Heater ApparatusC1155 Practice for Determining Thermal Resistance ofBuilding Env

12、elope Components from the In-Situ DataC1363 Test Method for Thermal Performance of BuildingMaterials and Envelope Assemblies by Means of a HotBox Apparatus2.2 ISO Standards:3ISO 9869-1 Thermal insulation Building elements In-situmeasurement of thermal resistance and thermal transmit-tance Part 1:Hea

13、t flow meter method3.Terminology3.1 DefinitionsFor definitions of terms relating to thermalinsulating materials,see Terminology C168.3.2 Definitions of Terms Specific to This Standard:1This practice is under the jurisdiction of ASTM Committee C16 on ThermalInsulation and is the direct responsibility

14、 of Subcommittee C16.30 on ThermalMeasurement.Current edition approved Sept.1,2017.Published October 2017.Originallyapproved in 1989.Last previous edition approved in 2012 as C1130 07(2012).DOI:10.1520/C1130-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Custome

15、r Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from International Organization for Standardization(ISO),ISOCentral Secretariat,BIBC II,Chemin de Blandonnet 8,CP 401,1214 Vernier,Geneva,Switze

16、rland,http:/www.iso.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2.1 maskmaterial(or materials)having the same,orne

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2