1、Designation:C1101/C1101M06(Reapproved 2012)Standard Test Methods forClassifying the Flexibility or Rigidity of Mineral FiberBlanket and Board Insulation1This standard is issued under the fixed designation C1101/C1101M;the number immediately following the designation indicates the yearof original ado
2、ption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods cover the procedures for the classi-fication of mineral fi
3、ber insulation as flexible,resilient flexible,semirigid,or rigid.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningv
4、alues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine th
5、e applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C168 Terminology Relating to Thermal Insulation3.Terminology3.1 DefinitionsTerminology C168 shall be considered asapplying to the terms used in these test methods.4.Significance and Use4.1 Classificatio
6、n of insulation relative to flexibility orrigidity is useful in establishing installation and applicationcharacteristics.5.Apparatus5.1 Iron Pipe,12-in.NPS(outside diameter 0.840 in.21.3mm)measuring at least 12 in.305 mm in length.5.2 Rigidity Tester,consisting of two horizontal,parallel,12-in.NPS i
7、ron pipe supports(outside diameter 0.840 in.21.3mm)at least 24 in.610 mm long and spaced 30 in.762 mmapart and horizontally to each other.6.Sampling6.1 Atest sample shall consist of one representative packageof insulation.One test specimen measuring 12 in.by 12 in.305 by 305 mm and of full thickness
8、 shall be randomly cutfrom the sample for flexibility testing.If the rigidity portion ofthe procedure is to be performed,a test specimen measuring 32in.813 mm long,and between 6 and 24 in.152 and 610 mmwide,and of full thickness shall be randomly cut from thesample.7.Procedure7.1 Test for Flexibilit
9、yBend the 12 by 12-in.305 by305-mm piece of insulation over the12in.NPS iron pipethrough an angle of 90 and examine the outer surface forvisible rupture.7.2 Test for Resilient FlexibilityIf no rupture occurs afterundergoing the 90 bending in 7.1,release the bent insulation.7.3 If the insulation is n
10、ot classified as flexible or resilientflexible,it shall be tested in accordance with 7.4 to determinethe degree of rigidity.7.4 Test for Semirigidity and RigidityPlace the 32 in.813mm long piece of insulation on the two horizontal,parallel,12-in.NPS iron pipe supports spaced 30 in.762 mm apart.After
11、 5 min have elapsed,measure the sag of the insulation tothe nearest 0.05 in.1.3 mm at the center of the span,from astraight line connecting two points on the insulations surfacedirectly above the supports.8.Interpretation of Results8.1 Test for FlexibilityIf there is no visible rupture,classify the
12、material as flexible.8.2 Test for Resilient FlexibilityIf the insulation is classi-fied as flexible in accordance with 8.1 and it springs back to itsoriginal form when it is released,classify it as resilient flexible.8.3 Test for Semirigidity:1These test methods are under the jurisdiction of ASTM Co
13、mmittee C16 onThermal Insulation and are the direct responsibility of Subcommittee C16.32 onMechanical Properties.Current edition approved May 1,2012.Published July 2012.Originally approvedin 1988.Last previous edition approved in 2006 as C1101/C1101M 06.DOI:10.1520/C1101_C1101M-06R12.2For reference
14、d ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken
15、,PA 19428-2959.United States1 8.3.1 If the sag is greater than12in.13 mm,the product isclassified as semirigid.8.3.2 If the test material fails to remain suspended,it isneither semirigid nor rigid and must be classified by theflexibility test as flexible or resilient flexible.8.4 Test for RigidityIf
16、,after undergoing the test in 7.4,thesag is12in.13 mm or less,the product is classified as rigid.8.5 Due to the inaccuracy of the sag measurement,there isan uncertainty of 0.05 in.1.3 mm.Therefore,for sagmeasurements at the rigid-semirigid determination point,agreater number of sample measurements is necessary in orderto make a valid determination of rigidity.9.Precision and Bias9.1 No information is presented about either the precision orbias for Test Methods C1101/C 1101M for classifying flexi
