1、Designation:C136/C136M14Standard Test Method forSieve Analysis of Fine and Coarse Aggregates1This standard is issued under the fixed designation C136/C136M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A n
2、umber in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers the determination of the part
3、iclesize distribution of fine and coarse aggregates by sieving.1.2 Some specifications for aggregates which reference thistest method contain grading requirements including bothcoarse and fine fractions.Instructions are included for sieveanalysis of such aggregates.1.3 UnitsThe values stated in eith
4、er SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in non-conformance with the standard.NOTE1Sieve size
5、is identified by its standard designation in Speci-fication E11.The alternative designation given in parentheses is forinformation only and does not represent a different standard sieve size.Specification E11 cites the following with respect to SI units versusinch-pound units as standard.“The values
6、 stated in SI units shall beconsidered standard for the dimensions of the sieve cloth openings and thewire diameters used in the sieve cloth.The values stated in inch-poundunits shall be considered standard with regard to the sieve frames,pans,”and covers.1.4 This standard does not purport to addres
7、s all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C117 Test Method for
8、 Materials Finer than 75-m(No.200)Sieve in Mineral Aggregates by WashingC125 Terminology Relating to Concrete and Concrete Ag-gregatesC637 Specification for Aggregates for Radiation-ShieldingConcreteC670 Practice for Preparing Precision and Bias Statementsfor Test Methods for Construction MaterialsC
9、702 Practice for Reducing Samples ofAggregate to TestingSizeD75 Practice for Sampling AggregatesE11 Specification for Woven Wire Test Sieve Cloth and TestSieves2.2 AASHTO Standard:AASHTO No.T 27 Sieve Analysis of Fine and CoarseAggregates33.Terminology3.1 DefinitionsFor definitions of terms used in
10、thisstandard,refer to Terminology C125.4.Summary of Test Method4.1 A sample of dry aggregate of known mass is separatedthrough a series of sieves of progressively smaller openings fordetermination of particle size distribution.5.Significance and Use5.1 This test method is used primarily to determine
11、 thegrading of materials proposed for use as aggregates or beingused as aggregates.The results are used to determine compli-ance of the particle size distribution with applicable specifica-tion requirements and to provide necessary data for control ofthe production of various aggregate products and
12、mixturescontaining aggregates.The data may also be useful in devel-oping relationships concerning porosity and packing.5.2 Accurate determination of material finer than the 75-m(No.200)sieve cannot be achieved by use of this test methodalone.Test Method C117 for material finer than 75-m sieve bywash
13、ing should be employed.5.3 Refer to methods of sampling and testing in Specifica-tion C637 for heavyweight aggregates.1This test method is under the jurisdiction of ASTM Committee C09 onConcrete and Concrete Aggregates and is the direct responsibility of SubcommitteeC09.20 on Normal Weight Aggregate
14、s.Current edition approved Dec.1,2014.Published February 2015.Originallyapproved in 1938.Last previous edition approved in 2006 as C136 06.DOI:10.1520/C0136_C0136M-14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book
15、 of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Association of State Highway and TransportationOfficials,444 North Capitol St.N.W.,Suite 225,Washington,DC 20001.*A Summary of Changes section appears at the end of this stan
16、dardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.Apparatus6.1 BalancesBalances or scales used in testing fine andcoarse aggregate shall have readability and accuracy as fol-lows:6.1.1 For fine aggregate,readable to 0.1 g and accurate to0.1 g or 0.1%of the test load,whichever is greater,at anypoint within the range of use.6.1.2 For coarse aggregate,or mixtures of fine and coarseaggregate,readable and accurate to 0.5 g or 0.1%of th
