1、Designation:C172917Standard Specification forAluminum Jacketing for Insulation1This standard is issued under the fixed designation C1729;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenthese
2、s indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers aluminum jacketing for ther-mal and acoustical insulation operating at either above orbelow ambient temperatures and in both indoor a
3、nd outdoorlocations.It does not cover insulation jacketing made fromother materials such as mastics,fiber reinforced plastic,PVC,or stainless steel nor does it cover the details of thermal oracoustical insulation systems.1.2 This specification provides physical requirements foraluminum jacketing for
4、 thermal and acoustical insulation.Guide C1423 provides guidance in selecting jacketing materi-als and their safe use.1.3 This is a material specification and does not imply anyperformance of the installed system using the materials speci-fied herein.For information about installation of aluminumjac
5、keting,see(1).21.4 The values stated in inch-pound units are to be regardedas standard.No other units of measurement are included in thisstandard.NOTE1A version of this specification in SI units is available asC1729M.1.5 This standard does not purport to address all of thesafety concerns,if any,asso
6、ciated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principl
7、es on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3B209 Specification for Aluminum and Alu
8、minum-AlloySheet and PlateB487 Test Method for Measurement of Metal and OxideCoating Thickness by Microscopical Examination ofCross SectionC168 Terminology Relating to Thermal InsulationC450 Practice for Fabrication of Thermal Insulating FittingCovers for NPS Piping,and Vessel LaggingC585 Practice f
9、or Inner and Outer Diameters of ThermalInsulation for Nominal Sizes of Pipe and TubingC835 Test Method for Total Hemispherical Emittance ofSurfaces up to 1400CC1371 Test Method for Determination of Emittance ofMaterials Near Room Temperature Using Portable Emis-sometersC1423 Guide for Selecting Jack
10、eting Materials for ThermalInsulationC1729M Specification for Aluminum Jacketing for Insula-tionC1785 Test Method for Concentration of Pinhole Detectionsin Moisture Barriers on Metal JacketingD3363 Test Method for Film Hardness by Pencil TestE84 Test Method for Surface Burning Characteristics ofBuil
11、ding MaterialsF1249 Test Method for Water Vapor Transmission RateThrough Plastic Film and Sheeting Using a ModulatedInfrared Sensor2.2 AAMA Standard:4AAMA 2605 Specification,Performance Requirements andTest Procedures for Superior Performing Organic Coat-ings on Aluminum Extrusions and Panels(with C
12、oilCoating Appendix)1This specification is under the jurisdiction of ASTM Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.40 onInsulation Systems.Current edition approved May 1,2017.Published May 2017.Originallyapproved in 2010.Last previous edition approved i
13、n 2016 as C1729 16a.DOI:10.1520/C1729-17.2The boldface numbers in parentheses refer to a list of references at the end ofthis standard.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informa
14、tion,refer to the standards Document Summary page onthe ASTM website.4Available from American Architectural Manufacturers Association(AAMA),1827 Walden Office Square,Suite 550,Schaumburg,IL 60173-4268,http:/www.aamanet.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohoc
15、ken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organizati
16、on Technical Barriers to Trade(TBT)Committee.1 2.3 ANSI Standard:5ANSI H35.2/H35.2(M)Dimensional Tolerances for Alumi-num Mill Products3.Terminology3.1 DefinitionsDefinitions in Terminology C168 apply toterms used in this specification.3.2 Definitions of Terms Specific to This Standard:3.2.1 box ribaluminum sheet formed to have alternatingparallel grooves and ridges with a cross section approximatinga square wave.3.2.2 cladding(as related to insulation jacketing)synonymous with jacketing.3.2.2.1
