收藏 分享(赏)

ASTM_C_1736_-_11.pdf

上传人:益****师 文档编号:185446 上传时间:2023-03-04 格式:PDF 页数:4 大小:102.71KB
下载 相关 举报
ASTM_C_1736_-_11.pdf_第1页
第1页 / 共4页
ASTM_C_1736_-_11.pdf_第2页
第2页 / 共4页
ASTM_C_1736_-_11.pdf_第3页
第3页 / 共4页
ASTM_C_1736_-_11.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:C173611Standard Practice forNon-Destructive Evaluation of Adhesion of InstalledWeatherproofing Sealant Joints Using a Rolling Device1This standard is issued under the fixed designation C1736;the number immediately following the designation indicates the year oforiginal adoption or,in the

2、 case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 The non-destructive procedure described in this practiceinduces a depression(strain)in the se

3、alant,creating an elon-gation of the sealant and a stress on the adhesive bond at thesealant to joint substrate interface.The primary purpose of thepractice is to reveal sealant adhesion anomalies not discernibleby visual examination,at the time of the evaluation,which mayaffect air infiltration res

4、istance,or water infiltration resistance,or both,of the sealed joint.NOTE1The nondestructive procedure may require immediate repairof the sealant bead,if failure is identified.Appropriate materials andequipment should be available for this purpose.1.2 This practice is useful for the evaluation of ad

5、hesion ofweatherseals in joints that are backed with compressiblematerials such as backer rod.This practice is not as useful injoints with solid backing.1.3 The proper use of this practice requires a workingknowledge of the principles of sealants as applied in movementjoint applications.1.4 A sealan

6、t fails to perform as a weatherseal when itallows air,or water,or both,to infiltrate the joint.This practicedoes not evaluate the performance of an installed sealant as aweatherseal.This practice is intended to only evaluate thecharacteristics of the adhesive bond in a particular installation.NOTE2I

7、n addition to identifying adhesion characteristics of thesealant joint,this practice may provide the user with an indication of othercharacteristics and anomalies including,but not limited to,changes insealant depth,insufficiently sized or configured backer rods,cohesivefailures,entrapped air voids,

8、and solid contaminants.Anomalies of thisnature may be interpreted and addressed by the evaluator.1.5 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.6 The committee with jurisdiction for this standard is notaware of any compara

9、ble standard published by other organi-zations.1.7This standard does not purport to address all of thesafety problems,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulato

10、ry limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C717 Terminology of Building Seals and SealantsC1193 Guide for Use of Joint SealantsC1472 Guide for Calculating Movement and Other EffectsWhen Establishing Sealant Joint Width3.Terminology3.1 DefinitionsRefer to Terminology C717 f

11、or definitionsof the terms used in this standard.3.2 Definitions of Terms Specific to This Standard:3.2.1 target depression,nThe amount of depressionneeded to reveal sealant adhesion anomalies,determined eitherin field or in laboratory,during or prior to a sealant evaluation,when using a device with

12、 a rolling component.4.Significance and Use4.1 Many parameters contribute to the overall performanceof a sealant application.Some of the most significant param-eters are sealant joint geometry,joint movement,joint design,sealant movement capability,quality of workmanship,qualityof adhesive bond,and

13、quality of the sealant material.4.2 If a sealant fails in adhesion,there is no straightforwardprocedure for determining the cause.The adhesive failure maybe due to workmanship,the specific surface preparation used,the specific sealant used,poor joint design,poor bondchemistry,or other causes.Compreh

14、ensive information for theuse of joint sealants is provided in Guide C1193.4.3 This technique may not produce useful results when thesealant is in compression.Comprehensive information regard-ing the impact of temperature on sealant joint dimensions maybe found in Guide C1472.1This practice is under

15、 the jurisdiction of ASTM Committee C24 on BuildingSeals and Sealants and is the direct responsibility of Subcommittee C24.30 onAdhesion.Current edition approved July 1,2011.Published August 2011.DOI:10.1520/C1736-11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM C

16、ustomer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.Testing Equipment5.1 Non-Permanent Marking EquipmentThe followingmay be used to perform location marking for repairs of failedsealant adhesion:5.1.1 Substrate MarkingRemovable non-residue tape,non-permanent self adhesive labels,or other

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2