收藏 分享(赏)

ASTM_D_1101_-_97a_2013.pdf

上传人:益****师 文档编号:185818 上传时间:2023-03-04 格式:PDF 页数:3 大小:72.93KB
下载 相关 举报
ASTM_D_1101_-_97a_2013.pdf_第1页
第1页 / 共3页
ASTM_D_1101_-_97a_2013.pdf_第2页
第2页 / 共3页
ASTM_D_1101_-_97a_2013.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D110197a(Reapproved 2013)Standard Test Methods forIntegrity of Adhesive Joints in Structural Laminated WoodProducts for Exterior Use1This standard is issued under the fixed designation D1101;the number immediately following the designation indicates the year oforiginal adoption or,in the

2、 case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe integrity of adhesive joints for structural laminated wood members,such as laminated arc

3、hesand beams,should be at least equal to that of the wood.Because initial strength tests generally are notan adequate measure of integrity of adhesive joints under severe service conditions,a test thatsimulates the effects of exterior exposure has been devised to evaluate adhesive joints in structur

4、allaminated wood members intended for this type of service.1.Scope1.1 These test methods cover an accelerated means ofmeasuring the resistance to delamination of structural lami-nated wood members intended for exterior service.1.2 These test methods are not intended as substitutes orreplacements for

5、 the more severe test of resistance to delami-nation in Specification D2559.1.3 Two test methods are included.Choice of test methoddepends on purpose of the test and available time to complete.1.3.1 Test Method AThis test requires 3 days to completeand is a method for determining the suitability of

6、adhesives andmanufacturing techniques and equipment for production ofjoints adequate for exterior service.1.3.2 Test Method BThis test requires approximately 1212h.(If excessive delamination occurs,the cycle is repeated).Itis a quality-control type test for examining adhesive jointquality.1.4 The va

7、lues stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safe

8、ty and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D907 Terminology of AdhesivesD2559 Specification for Adhesives for Bonded StructuralWood Products for Use Under Exterior Exposure Condi-tions2.2 Other Standards:3

9、ANSI A190.12012 American Nation Standard for WoodProductsStructural Glued Laminated Timber3.Terminology3.1 DefinitionsMany terms in these test methods aredefined in Terminology D907.3.1.1 glulam,nsynonym for structural-glued-laminatedtimber.3.1.2 structural-glued-laminated timber,nan engineeredstres

10、s-rated product of a timber laminating plant comprisingassemblies of specially selected and prepared wood lamina-tions securely bonded together with adhesives,with the fol-lowing characteristics:(1)the grain of all laminations isapproximately parallel longitudinally;and(2)the laminationsmay be compr

11、ised of pieces end-joined to form any length,ofpieces placed or glued edge-to-edge to make wider ones or ofpieces bent to curved form during gluing.(Synonym glulam)ANSI A190.1-2012.American National Standard for WoodProductsStructural Laminated.3.2 Definitions of Terms Specific to This Standard:1The

12、se test methods are under the jurisdiction of ASTM Committee D14 onAdhesives and are the direct responsibility of Subcommittee D14.30 on WoodAdhesives.Current edition approved May 1,2013.Published July 2013.Originally approvedin 1997.Last previous edition approve in 2006 as D1101 97a(2006).DOI:10.15

13、20/D1101-97AR13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Instit

14、ute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.2.1 laminated wood,nthe fabricated product resultingfrom the bonding of two or more laminations,with eachlamination m

15、ade from one or more pieces bonded eitherlengthwise,edgewise,or both,and all with the direction of thegrain essentially parallel,to form a larger piece such as astructural member.4.Significance and Use4.1 The test is suitable for check testing properly selectedsamples from regular production or for

16、determining the suit-ability of adhesives and bonding techniques for the productionof joints for exterior service.4.2 Vary the number of specimens taken from each memberand the number of members selected for test depending on thetotal number of members involved and the purpose of the tests.It is advisable,however,to include at least three specimens inthe test,with the specimens selected to represent the probablerange of quality of the adhesive joints.4.3 Adhesive joints at knots and knotty areas

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2