收藏 分享(赏)

ASTM_C_454_-_10_2017.pdf

上传人:益****师 文档编号:185865 上传时间:2023-03-04 格式:PDF 页数:2 大小:66KB
下载 相关 举报
ASTM_C_454_-_10_2017.pdf_第1页
第1页 / 共2页
ASTM_C_454_-_10_2017.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:C45410(Reapproved 2017)Standard Test Method forDisintegration of Carbon Refractories by Alkali1This standard is issued under the fixed designation C454;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi

2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the behavior of carbon refrac-tories when subjected to the action of an alkali at an elevatedtemperature.Thi

3、s destructive condition as encountered inservice is accelerated in the test to show in a short time theprobable behavior of the carbon refractory during use.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units

4、 that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the a

5、pplica-bility of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued

6、by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Significance and Use2.1 The disintegration of carbon refractories by alkali attackat elevated temperatures is an important consideration in usingthese materials for certain applications.Disruption of carbonrefractories in the

7、 test is sensitive to a number of variables,including alkali concentration,temperature,and the presenceof water vapor.The procedure is suitable for guidance inproduct development and for relative comparisons in applica-tion work such as in blast furnace service.3.Apparatus and Materials3.1 SaggerA s

8、agger,and coke breeze passing a No.4(4.75-mm)sieve.3.2 KilnThe kiln shall be capable of maintaining thespecified rate of heating.During the temperature holdingperiod,the temperature distribution over the hearth shall notvary more than 615 F(8 C).3.3 Potassium Carbonate(K2CO3)Anhydrous granular.4.Tes

9、t Specimens4.1 Ten specimens constitute a specimen set and not morethan one specimen is taken from a given carbon shape.4.2 Two-inch(51-mm)cube specimens are cut from theshapes to a manner so as to maintain as many of the originalsurfaces as possible.4.3 A hole78in.(22 mm)in diameter and 1 in.(25 mm

10、)deep is drilled into the center of one face of each specimen.4.4 Cut a lid from a carbon shape measuring approximately2 by 2 by14in.(50 by 50 by 6 mm)for each specimen.5.Procedure5.1 Dry the specimens and lids at 220 to 230 F(105 to110 C)for at least 1 h.Place 8 g of K2CO3in the hole of eachspecime

11、n,and then place a lid over each hole.5.2 Place the prepared specimens in the sagger,using cokebreeze as a packing material to prevent oxidation.Maintain adistance of not less than 1 in.(25 mm)between the inner wallof the sagger and any specimen,and not less than14in.(6 mm)between specimens.Cover th

12、e uppermost specimen with alayer of coke breeze at least 1 in.in thickness and place aclose-fitting cover on the sagger.The lid may be sealed in placearound the outside of the sagger by the use of air-settingrefractory mortar.5.3 Heat the sagger assembly in the kiln at a rate notexceeding 360 F(200

13、C)h until 1750 F(955 C)isreached;maintain that temperature within 615 F(8.5 C)for5 h.5.4 During the cooling period,remove the specimens fromthe sagger before they reach 210 F(100 C)and store,untilexamined and photographed,in a desiccator or drying ovenoperating at 220 to 230 F(105 to 110 C).NOTE1If

14、there is a delay between preparing(5.1)and heating(5.3)the specimens,store them or the sagger-specimen assemblage in adesiccator or in an oven maintained at 220 to 230 F(105 to 110 C)untilthe procedure is continued.1This test method is under the jurisdiction of ASTM Committee C08 onRefractories and

15、is the direct responsibility of Subcommittee C08.04 on ChemicalBehaviors.Current edition approved May 1,2017.Published May 2017.Originallyapproved in 1960.Last previous edition approved in 2010 as C454 10.DOI:10.1520/C0454-10R17.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Con

16、shohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 6.Report6.1 Report the condition of each test specimen upon beingremoved from the sagger,and attach a photograph to thewritten report.The photograp

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2