1、Designation:C54918Standard Specification forPerlite Loose Fill Insulation1This standard is issued under the fixed designation C549;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indi
2、cates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers the composition and physicalproperties of expanded per
3、lite loose fill insulation.The speci-fication also includes the testing procedures by which theacceptability of the material is determined.These testingprocedures deal primarily with material performance in thetemperature range associated with the thermal envelope ofbuildings;however,the commerciall
4、y usable temperaturerange for this insulation is from 459 to 1400F(1 to 1033 K).For specialized applications,refer to the manufacturers in-structions.1.2 The specification also covers the composition and prop-erties of perlite that has been surface-treated to produce dustsuppression for installation
5、s where dust is a factor.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 The following applies to Test Methods E84 and E136This st
6、andard is used to measure and describe the response ofmaterials,products,or assemblies to heat and flame undercontrolled conditions,but does not by itself incorporate allfactors required for fire hazard or fire risk assessment of thematerials,products,or assemblies under actual fire conditions.1.5 T
7、he following applies to Test Methods E84 and E136Fire testing is inherently hazardous.Adequate safeguards forpersonnel and property shall be employed in conducting thesetests.1.6 When the installation or use of thermal insulationmaterials,accessories and systems,may pose safety or healthproblems,the
8、 manufacturer shall provide the user appropriatecurrent information regarding any known problems associatedwith the recommended use of the companys products,andshall also recommend protective measures to be employed intheir safe utilization.The user shall establish appropriatesafety and health pract
9、ices and determine the applicability ofregulatory requirements prior to use.For additional precau-tionary statements,see Section 12.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish
10、 appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for th
11、eDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C136 Test Method for Sieve Analysis of Fine and CoarseAggregatesC168 Terminology Relating to Thermal Insulatio
12、nC177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarded-Hot-Plate ApparatusC390 Practice for Sampling and Acceptance of ThermalInsulation LotsC518 Test Method for Steady-State Thermal TransmissionProperties by Means of the Heat Flow Meter
13、 ApparatusC520 Test Methods for Density of Granular Loose FillInsulationsE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE136 Test Method for Behavior of Materials in a VerticalTube Furnace at 750CE177 Practice for Use of the Terms Precision and Bias inASTM Test Methods1This
14、specification is under the jurisdiction of ASTM Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.23 onBlanket and Loose Fill Insulation.Current edition approved Nov.1,2018.Published November 2018.Originallyapproved in 1964.Last previous edition approved in 2012
15、 as C549 06(2012).DOI:10.1520/C0549-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM Internationa
16、l,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.Terminology3.1 Terms used in this specification are defined in Termi-nology C168.4.Classification4.1
