1、Designation:B16711(Reapproved 2016)Standard Specification forNickel-Chromium-Iron Alloys(UNS N06600,N06601,N06603,N06690,N06693,N06025,N06045,and N06696),Nickel-Chromium-Cobalt-Molybdenum Alloy(UNS N06617),andNickel-Iron-Chromium-Tungsten Alloy(UNS N06674)Seamless Pipe and Tube1This standard is issu
2、ed under the fixed designation B167;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the
3、 last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification2covers nickel-chromium-iron alloys(UNS N06600,N06601,N06603,N06690,N06693,N06025,N06045,and N06696),3nickel-chromium-cobalt-molybdenumalloy(UNS N06617),and
4、nickel-iron-chromium-tungsten al-loy UNS N06674),in cold-worked annealed,hot-workedannealed,and hot-finished seamless pipe and tube intended forgeneral corrosion resistant and heat resistant applications.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in pare
5、ntheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following safety hazards caveat pertains only to thetest methods portion,Section 13,of this specification:Thisstandard does not purport to address all of the safety concerns,
6、if any,associated with its use.It is the responsibility of the userof this standard to become familiar with all hazards includingthose identified in the appropriate Safety Data Sheet(SDS)forthis product/material as provided by the manufacturer,toestablish appropriate safety and health practices,and
7、deter-mine the applicability of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:4B829 Specification for General Requirements for Nickel andNickel Alloys Seamless Pipe and TubeB880 Specification for General Requirements for ChemicalCheck Analysis Limits for Nickel,Nickel
8、Alloys andCobalt AlloysE8 Test Methods for Tension Testing of Metallic MaterialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE38 Methods for Chemical Analysis of Nickel-Chromiumand Nickel-Chromium-Iron Alloys(Withdrawn 1989)5E112 Test Methods for
9、Determining Average Grain SizeE527 Practice for Numbering Metals and Alloys in theUnified Numbering System(UNS)E1473 Test Methods for Chemical Analysis of Nickel,Co-balt and High-Temperature Alloys2.2 Federal Standards:6Fed.Std.No.102 Preservation,Packaging and PackingLevelsFed.Std.No.123 Marking fo
10、r Shipment(Civil Agencies)Fed.Std.No.182 Continuous Identification Marking ofNickel and Nickel-Base Alloys1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their A
11、lloys.Current edition approved June 1,2016.Published June 2106.Originallyapproved in 1941.Last previous edition approved in 2011 as B167 11.DOI:10.1520/B0167-11R16.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SB-167 in Section II of that Code.3New designation est
12、ablished in accordance with Practice E527 and SAEJ 1086,Practice for Numbering Metals and Alloys(UNS).4For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Docum
13、ent Summary page onthe ASTM website.5The last approved version of this historical standard is referenced onwww.astm.org.6Available from DLA Document Services,Building 4/D,700 Robbins Ave.,Philadelphia,PA 19111-5094,http:/quicksearch.dla.mil.*A Summary of Changes section appears at the end of this st
14、andardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.3 Military Standard:6MIL-STD-129 Marking for Shipment and Storage3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 average diameter,nthe average of the maximum an
15、dminimum outside diameters,as determined at any one crosssection of the pipe or tube.3.1.2 pipe,ntube conforming to the particular dimensionscommercially known as pipe sizes.See Table X2.1.3.1.3 seamless pipe or tube,na pipe or tube produced witha continuous periphery in all stages of the operations
16、.3.1.4 tube,na hollow product of round or any other crosssection having a continuous periphery.4.Ordering Information4.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for the safe and satisfactoryperformance of material ordered under this specification.Examples of such requirements include,but are not limited to,the following:4.1.1 Alloy Name or UNS Numbersee Table 1,4.1.2 ASTM Designation,including year of issue,4.1.3 Condition(see Appendix X3),4.1.4 Fi
