1、Designation:B68997(Reapproved 2018)1Standard Specification forElectroplated Engineering Nickel Coatings1This standard is issued under the fixed designation B689;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio
2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEReference links in subsection 6.5 updated editorially in August 2018.This standard has been approved for use by agencies of the U.S.Departmen
3、t of Defense.1.Scope1.1 This specification covers the requirements for electro-plated nickel coatings applied to metal products for engineer-ing applications,for example,for use as a buildup for misma-chined or worn parts,for electronic applications,including asunderplates in contacts or interconnec
4、tions,and in certainjoining applications.1.2 Electroplating of nickel for engineering applications(Note 1)requires technical considerations significantly differ-ent from decorative applications because the following func-tional properties are important:1.2.1 Hardness,strength,and ductility,1.2.2 Wea
5、r resistance,1.2.3 Load bearing characteristics,1.2.4 Corrosion resistance,1.2.5 Heat scaling resistance,1.2.6 Fretting resistance,and1.2.7 Fatigue resistance.NOTE1Functional electroplated nickel coatings usually contain about99%nickel,and are most frequently electrodeposited from a Watts nickelbath
6、 or a nickel sulfamate bath.Typical mechanical properties of nickelelectroplated from these baths,and the combined effect of bath operationand solution composition variables on the mechanical properties of theelectrodeposit are given in Guide B832.When electroplated nickel isrequired to have higher
7、hardnesses,greater wear resistance,certainresidual stress values and certain leveling characteristics,sulfur and othersubstances are incorporated in the nickel deposit through the use of certainaddition agents in the electroplating solution.For the effect of suchadditives,see Section 4 and Annex A3.
8、Cobalt salts are sometimes addedto the plating solution to produce harder nickel alloy deposits.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and envi
9、ronmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standa
10、rds,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2B183 Practice for Preparation of Low-Carbon Steel forElectroplatingB242 Guide for Preparation of High-Carbon Steel for Elec-troplatingB252 Guide f
11、or Preparation of Zinc Alloy Die Castings forElectroplating and Conversion CoatingsB253 Guide for Preparation of Aluminum Alloys for Elec-troplatingB254 Practice for Preparation of and Electroplating onStainless SteelB281 Practice for Preparation of Copper and Copper-BaseAlloys for Electroplating an
12、d Conversion CoatingsB320 Practice for Preparation of Iron Castings for Electro-platingB322 Guide for Cleaning Metals Prior to ElectroplatingB343 Practice for Preparation of Nickel for Electroplatingwith NickelB374 Terminology Relating to ElectroplatingB480 Guide for Preparation of Magnesium and Mag
13、nesiumAlloys for ElectroplatingB487 Test Method for Measurement of Metal and OxideCoating Thickness by Microscopical Examination ofCross SectionB499 Test Method for Measurement of Coating Thicknessesby the Magnetic Method:Nonmagnetic Coatings onMagnetic Basis MetalsB507 Practice for Design of Articl
14、es to Be Electroplated onRacks1This specification is under the jurisdiction of ASTM Committee B08 onMetallic and Inorganic Coatings and is the direct responsibility of SubcommitteeB08.03 on Engineering Coatings.Current edition approved June 1,2018.Published June 2018.Originallyapproved in 1981.Last
15、previous edition approved in 2013 as B689 97(2013).DOI:10.1520/B0689-97R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM
16、 website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 B530 Test Method for Measurement of Coating Thicknessesby the Magne
