收藏 分享(赏)

ASTM_A_899_-_91_2014.pdf

上传人:益****师 文档编号:186198 上传时间:2023-03-04 格式:PDF 页数:3 大小:60.79KB
下载 相关 举报
ASTM_A_899_-_91_2014.pdf_第1页
第1页 / 共3页
ASTM_A_899_-_91_2014.pdf_第2页
第2页 / 共3页
ASTM_A_899_-_91_2014.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:A89991(Reapproved 2014)Standard Specification forSteel Wire,Epoxy-Coated1This standard is issued under the fixed designation A899;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in paren

2、theses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers steel wire in the size range of0.120 to 0.500 in.(3.05 to 12.7 mm)with three classes ofprotective epoxy coating,in coils,for gen

3、eral use.Class Acoating is intended for use for moderate corrosion protection,Class B coating for more severe protection,and Class C forsevere corrosion and abrasion protection.NOTE1The coating applicator is identified throughout this specifica-tion as the manufacturer.1.2 The values stated in inch-

4、pound units are to be regardedas the standard.The SI units given in parentheses are forinformation only.2.Referenced Documents2.1 ASTM Standards:2A510 Specification for General Requirements for Wire Rodsand Coarse Round Wire,Carbon SteelA775/A775M Specification for Epoxy-Coated Steel Rein-forcing Ba

5、rsA853 Specification for Steel Wire,Carbon,for General UseG12 Test Method for Nondestructive Measurement of FilmThickness of Pipeline Coatings on Steel(Withdrawn2013)33.Ordering Information3.1 The purchaser shall specify the following:3.1.1 Wire size(the nominal diameter of the coated wire),3.1.2 Qu

6、antity,3.1.3 Class of coating,and3.1.4 Method of packaging,such as,coils,coils on steelreels,etc.3.2 The purchaser may specify the following if desired:3.2.1 Requirements for certification(see 14.1),3.2.2 Requirements for patching material(see 4.3),3.2.3 Specific requirements for test frequency(see

7、8.1),and3.2.4 Requirements for outside inspection of manufacturingplant.NOTE2A typical ordering description for wire is as follows:40 000lb of epoxy coated wire,ASTM A853,0.148 in.diameter,Grade 1018with a Class A epoxy coating in 1000 lb coils on steel reels to ASTMA899.4.Materials and Manufacture4

8、.1 Steel wire to be coated shall meet the requirements ofthe purchaser or the requirements of an applicable general wirespecification such as Specification A510 and SpecificationA853,and shall be free of surface contaminants such as oil,grease,or paint when received at the manufacturers plant andpri

9、or to cleaning and coating.4.2 The coating material shall meet the requirements listedin Annex A1 of Specification A775/A775M.4.2.1 If specified in the order,a written certification shall befurnished to the purchaser that properly identifies the numberof each batch of coating material used in the or

10、der,material,quantity represented,date of manufacture,name and address ofmanufacturer,and a statement that the supplied coating mate-rial meets the requirements of Annex A1 of SpecificationA775/A775M.4.3 If specified in the order,patching material,compatiblewith the coating material and meeting the

11、requirements ofAnnex A1 of Specification A775/A775M shall be supplied tothe purchaser.5.Surface Preparation5.1 The surface of the steel wire to be coated shall becleaned by abrasive blast cleaning or chemical cleaning prior tocoating to ensure proper adherence of the epoxy to the steelsurface.5.2 Pr

12、ior to abrasive blast cleaning,the surface of the wireto be coated may be cleaned in an aqueous solution to removeresidual wire drawing lubricants.6.Application of Coating6.1 The coating shall be applied to the cleaned surface assoon as possible after cleaning,and before oxidation of thesurface disc

13、ernible to the unaided eye occurs.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.03 on Steel Rod and Wire.Current edition approved March 1,2014.Published April 2014.Originallyapproved

14、 in 1990.Last previous edition approved in 2007 as A899 91(2007).DOI:10.1520/A0899-91R14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary p

15、age onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1Copyright by ASTM Intl(all rights reserved);6.2 The coating shall be applied and pro

16、perly cured inaccordance with the recommendations of the manufacturer ofthe coating material to satisfy the product requirements.7.Requirements for Coated Wire7.1 Thickness of Coating:7.1.1 Class AThe film thickness of the coating after curingshall be 5 mils minimum(0.13 mm).7.1.2 Class BThe film thickness of the coating aftercuring shall be 10 mils minimum(0.25 mm).7.1.3 Class CThe film thickness of the coating aftercuring shall be 20 mils minimum(0.51 mm).7.1.4 The thickness of the coating fil

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2