收藏 分享(赏)

ASTM_B_582_-_07_2013.pdf

上传人:益****师 文档编号:186268 上传时间:2023-03-04 格式:PDF 页数:3 大小:77.93KB
下载 相关 举报
ASTM_B_582_-_07_2013.pdf_第1页
第1页 / 共3页
ASTM_B_582_-_07_2013.pdf_第2页
第2页 / 共3页
ASTM_B_582_-_07_2013.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:B58207(Reapproved 2013)Standard Specification forNickel-Chromium-Iron-Molybdenum-Copper Alloy Plate,Sheet,and Strip1This standard is issued under the fixed designation B582;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,

2、the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 The specification2covers plate,sheet,and strip ofnickel-chromium-iron-molybdenum-copper alloys(UNSN06007,N06975

3、,N06985,and N06030)*as shown in Table 1,for use in general corrosive service.1.2 The following products are covered under this specifi-cation:1.2.1 Sheet and StripHot or cold rolled,solution annealed,and descaled unless solution anneal is performed in an atmo-sphere yielding a bright finish.1.2.2 Pl

4、ateHot or cold rolled,solution annealed,anddescaled.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport

5、 to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet(MSDS)for this product/materialas provided by the manufacturer,to establ

6、ish appropriatesafety and health practices,and determine the applicability ofregulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3B906 Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate,Sheet,and Strip3.Terminology3.1 Definitions of Terms S

7、pecific to This Standard:3.1.1 cold-rolled plate,nmaterial316to38in.(4.76 to9.52 mm),inclusive,in thickness.3.1.2 hot-rolled plate,nmaterial316in.(4.76 mm)andover in thickness.3.1.3plate,nmaterial316in.(4.76 mm)and over inthickness.3.1.4 sheet and strip,nmaterial under316in.(4.76 mm)inthickness.4.Ge

8、neral Requirements4.1 Materials furnished to this specification shall conform tothe applicable requirements of Specification B906 unlessotherwise provided herein.5.Ordering Information5.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered und

9、er thisspecification.Examples of such requirements include,but arenot limited to,the following:5.1.1 AlloyTable 1,5.1.2 DimensionsThickness(in decimals of an inch),width,and length(inch or fractions of an inch),5.1.3 Optional Requirement,PlateHow the plate is to becut(see 8.1 and Specification B906,

10、Table A2.3),5.1.4 CertificationState if certification or a report of testresults is required(Specification B906),5.1.5 Purchaser InspectionState which tests or inspec-tions are to be witnessed(Specification B906),and5.1.6 Samples for Product(Check)AnalysisState whethersamples should be furnished(Sec

11、tion 6).6.Chemical Composition6.1 Heat AnalysisThe material shall conform to the com-position limits specified in Table 1.6.2 Product(Check)AnalysisIf a product(check)analysisis made by the purchaser,the material shall conform to therequirements specified in Table 1 subject to the permissibletoleran

12、ces in Specification B906.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved Feb.1,2013.Published February 2013.Originallyappr

13、oved in 1973.Last previous edition approved in 2007 as B582 07.DOI:10.1520/B0582-07R13.2For ASME Boiler and Pressure Vessel Code applications,see related Specifi-cation SB-582 in Section II of that Code.*New designation established in accordance with ASTM E527 and SAE J1086,Practice for Numbering Me

14、tals and Alloys(UNS).3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor

15、Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 7.Mechanical Properties and Other Requirements7.1 Tensile PropertiesThe material shall conform to themechanical property requirements prescribed in Table 2.7.2 HardnessThe hardness values given in Table 2 areinformative only.8.Edges8.1

16、 Plates shall have sheared or cut machined,abrasive cut,powder cut,or inert arc cut edges,as specified.8.2 Sheet and strip shall have sheared or slit edges.9.Permissible Variations in Dimensions9.1 WeightFor calculation of mass or weight,the follow-ing densities shall be used:DensityAlloylb/in.3g/cm3N060070.3008.31N069750.2958.17N069850.3008.31N060300.2978.229.2 Thicknesses:9.2.1 PlateThe permissible variations in thickness of plateshall be as prescribed in Specification B906,Table A2.1.9.2.2 Sh

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2