1、Designation:B82417Standard Specification forGeneral Requirements for Copper Alloy Castings1This standard is issued under the fixed designation B824;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in
2、 parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification establishes general requirements com-mon to
3、 ASTM copper alloy casting specifications B22/B22M,B61,B62,B66,B67,B148,B176,B271/B271M,B369,B427,B505/B505M,B584,B763/B763M,B770,and B806.Theserequirements apply to the casting specifications to the extentreferenced therein.1.1.1 In the event of conflict between this specification anda casting spec
4、ification,the requirements of the casting speci-fication shall take precedence.1.2 The chemical composition and other requirements notincluded in this specification shall be prescribed in the castingproduct specifications.1.3 UnitsThe values stated in inch-pound units are to beregarded as standard.T
5、he values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.4 No precise quantitative relationship can be stated be-tween the properties of the metal in various locations of thesame casting or between the properties o
6、f castings and those ofa test bar casting from the same metal.(See Appendix X1.)21.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides
7、and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 The following documents,of the issue in effect on dateof casting purchase,form,part of this specification to the extentreferenced herein:2.2 ASTM Standards:3B22/B22M Specifi
8、cation for Bronze Castings for Bridgesand TurntablesB61 Specification for Steam or Valve Bronze CastingsB62 Specification for Composition Bronze or Ounce MetalCastingsB66 Specification for Bronze Castings for Steam Locomo-tive Wearing PartsB67 Specification for Car and Tender Journal Bearings,LinedB
9、148 Specification for Aluminum-Bronze Sand CastingsB176 Specification for Copper-Alloy Die CastingsB193 Test Method for Resistivity of Electrical ConductorMaterialsB194 Specification for Copper-BerylliumAlloy Plate,Sheet,Strip,and Rolled BarB208 Practice for Preparing Tension Test Specimens forCoppe
10、r Alloy Sand,Permanent Mold,Centrifugal,andContinuous CastingsB271/B271M Specification for Copper-Base Alloy Centrifu-gal CastingsB369 Specification for Copper-Nickel Alloy CastingsB427 Specification for Gear Bronze Alloy CastingsB505/B505M Specification for Copper Alloy ContinuousCastingsB584 Speci
11、fication for Copper Alloy Sand Castings forGeneral ApplicationsB763/B763M Specification for Copper Alloy Sand Castingsfor Valve ApplicationsB770 Specification for Copper-Beryllium Alloy Sand Cast-ings for General ApplicationsB806 Specification for Copper Alloy Permanent Mold Cast-ings for General Ap
12、plicationsB846 Terminology for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE10 Test Method for Brinell Hardness of Metallic Materials1This specification is under the jurisdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct responsibilit
13、y of Subcommittee B05.05 onCastings and Ingots for Remelting.Current edition approved April 1,2017.Published May 2017.Originallyapproved in 1992.Last previous edition approved in 2016 as B824-16.DOI:10.1520/B0824-17.2For ASME Boiler and Pressure Vessel Code application,see related specifica-tion in
14、Section II of that code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at t
15、he end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDe
16、velopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 E18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE54 Test Methods for Chemical Analysis of Special Brassesand Bronzes(Withdrawn 2002)4E62 Test Methods for Chemical Analysis of Copper andCopperAlloys(Photometric Methods)(Withdrawn 2010)4E76 Tes
