1、Designation:A1005/A1005M00(Reapproved 2010)Standard Specification forSteel Line Pipe,Black,Plain End,Longitudinal and HelicalSeam,Double Submerged-Arc Welded1This standard is issued under the fixed designation A1005/A1005M;the number immediately following the designation indicates theyear of origina
2、l adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers double submerged-arc welded,black,plain end ste
3、el pipe for use in the conveyance of fluidsunder pressure.Pipe in sizes NPS 16 and larger,as given inASME B36.10,are included;pipe having other dimensions,inthis size range,are permitted,provided such pipe complieswith all other requirements of this specification.1.2 It is intended that pipe be capa
4、ble of being welded in thefield when welding procedures in accordance with the require-ments of the applicable pipeline construction code are used.1.3 The values stated in either inch-pound units or in SIunits are to be regarded separately as standard.The values ineach system are not exact equivalen
5、ts,therefore,each system isto be used independently of the other,without combiningvalues in any way.1.4 The following precautionary statement pertains to thetest method portion,Section 14 of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with
6、 its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2A370 Test Methods and Definitions for Mechanical Testingof Steel Product
7、sA450/A450M Specification for General Requirements forCarbon and Low Alloy Steel TubesA530/A530M Specification for General Requirements forSpecialized Carbon and Alloy Steel PipeA751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel ProductsA941 Terminology Relating to Steel,Sta
8、inless Steel,RelatedAlloys,and Ferroalloys2.2 ASME Standards:3ASME B36.10 Welded and Seamless Wrought Steel PipeASME Boiler and Pressure Vessel Code,Section VIII,Unfired Pressure VesselsASME Boiler and Pressure Vessel Code,Section IX,Weld-ing and Brazing Qualifications2.3 API Publications:4API RP 5L
9、3 Recommended Practice for Conducting Drop-Weight Tear Tests on Line PipeAPI Standard 1104 Welding of Pipelines and Related Facili-ties3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 double submerged-arc welding,na welding processthat produces coalescence of metals by heating t
10、hem with anarc of arcs between a bare metal electrode or electrodes and thework pieces,using at least one pass from the inside and at leastone pass from the outside to make the longitudinal,helical,andskelp end weld seams,whichever are applicable,the arc or arcsand the molten metal are shielded by a
11、 blanket of granular,fusible material on the work pieces.3.1.2 jointer,nnot more than three lengths of pipe circum-ferentially welded together to produce a single length thatcomplies with the length provisions of this specification.3.1.3 skelp,nthe flat rolled product intended to be formedinto pipe.
12、3.1.4 skelp end,nthe weld joining the ends of two lengthsof skelp.3.1.5 specified outside diameter,nthe outside diametershown in ASME B36.10 or that stated on the order.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct r
13、esponsibility of SubcommitteeA01.09 on Carbon Steel Tubular Products.Current edition approved April 1,2010.Published August 2010.Originallyapproved in 2000.Last previous edition approved in 2004 as A1005/A1005M00(2004).DOI:10.1520/A1005_A1005M-00R10.2For referenced ASTM standards,visit the ASTM webs
14、ite,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Society of Mechanical Engineers(ASME),ASMEInternational Headquarters,Three Park Ave.,New Yo
15、rk,NY 10016-5990,http:/www.asme.org.4Available from American Petroleum Institute(API),1220 L.St.,NW,Washington,DC 20005-4070,http:/www.api.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesNOTICE:This standard has either been superseded a
16、nd replaced by a new version or withdrawn.Contact ASTM International(www.astm.org)for the latest information1 3.1.6 test lot,na quantity of pipe of the same ordereddiameter,heat,and wall thickness.3.2 DefinitionsFor definitions of other terms used in thisspecification,refer to Terminology A941.4.General Requirements4.1 Pipe furnished under this specification shall conform tothe applicable requirements of Specification A530/A530Munless otherwise provided herein.5.Ordering Information5.1 Informati
