1、Designation:A 1019/A 1019M 01(Reapproved 2007)Standard Specification forClosed Rib Steel Pipe with Diameter of 36 in.900 mm orLess,Polymer Precoated for Sewers and Drains1This standard is issued under the fixed designation A 1019/A 1019M;the number immediately following the designation indicates the
2、year of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers polymer precoated,closed ribste
3、el pipe,intended for use for storm water drainage,under-drains,the construction of culverts,and similar uses.Pipecovered by this specification is not normally used for theconveyance of sanitary or industrial wastes.The steel sheetused in fabrication of the pipe has a polymer protective coatingover a
4、 metallic coating of zinc.1.2 The polymer precoating provides extra protection of thebase metal against corrosion or abrasion,or both,in addition tothat provided by the metallic coating.Severe environments arelikely to cause corrosion problems to accessory items such ascoupling band hardware that do
5、es not have a polymer coatingunless supplemental protection is provided.Additional protec-tion for polymer precoated steel pipe is available by use ofcoatings applied after fabrication of the pipe as described inSpecification A 849.1.3 This specification does not include requirements forbedding,back
6、fill,or the relationship between earth cover loadand sheet thickness of the pipe.Experience with drainageproducts has shown that successful performance depends uponthe proper selection of rib depth,sheet thickness,type ofbedding and backfill,controlled manufacture in the plant,andcare in installatio
7、n.The installation procedure is described inPractice A 798/A 798M.1.4 This specification is applicable to orders in eitherinch-pound units as A 1019,or in SI units as A 1019M.Inch-pound units and SI units are not necessarily equivalent.SIunits are shown in brackets in the text for clarity,but they a
8、rethe applicable values when the material is ordered toA 1019M.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-b
9、ility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2A 90/A 90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA 153/A 153M Specification for Zinc Coating(Hot-Dip)onIron and Steel HardwareA 307 Specification for Carb
10、on Steel Bolts and Studs,60000 PSI Tensile StrengthA 563 Specification for Carbon and Alloy Steel NutsA 563M Specification for Carbon and Alloy Steel NutsMetricA 653/A 653M Specification for Steel Sheet,Zinc-Coated(Galvanized)or Zinc-Iron Alloy-Coated(Galvannealed)by the Hot-Dip ProcessA 742/A 742M
11、Specification for Steel Sheet,MetallicCoated and Polymer Precoated for Corrugated Steel PipeA 780 Practice for Repair of Damaged and Uncoated Areasof Hot-Dip Galvanized CoatingsA 796/A 796M Practice for Structural Design of Corru-gated Steel Pipe,Pipe-Arches,and Arches for Storm andSanitary Sewers a
12、nd Other Buried ApplicationsA 798/A 798M Practice for Installing Factory-Made Corru-gated Steel Pipe for Sewers and Other ApplicationsA 849 Specification for Post-Applied Coatings,Pavings,and Linings for Corrugated Steel Sewer and Drainage PipeA 902 Terminology Relating to Metallic Coated Steel Prod
13、-uctsA 924/A 924M Specification for General Requirements forSteel Sheet,Metallic-Coated by the Hot-Dip ProcessB 633 Specification for Electrodeposited Coatings of Zincon Iron and SteelB 695 Specification for Coatings of Zinc MechanicallyDeposited on Iron and SteelC 443 Specification for Joints for C
14、oncrete Pipe and Man-holes,Using Rubber GasketsD 1005 Test Method for Measurement of Dry-Film Thick-ness of Organic Coatings Using Micrometers1This specification is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility ofSubcommittee
15、A05.17 on Corrugated Steel Pipe Specifications.Current edition approved May 1,2007.Published July 2007.Originally approvedin 2001.Last previous edition approved in 2001 as A 1019/A 1019M-01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at servicea
16、stm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Copyright by ASTM Intl(all rights reserved);Sat May 30 10:17:05 EDT 2009Downloaded/printed byLaurentian University pursuant to License Agreement.No further reproductions authorized.D 1056 Specification for Flexible Cellular MaterialsSponge or Expanded Rubber,E 29 Pr
