收藏 分享(赏)

ASTM_A_474_-_03_2013.pdf

上传人:益****师 文档编号:186666 上传时间:2023-03-04 格式:PDF 页数:4 大小:76.96KB
下载 相关 举报
ASTM_A_474_-_03_2013.pdf_第1页
第1页 / 共4页
ASTM_A_474_-_03_2013.pdf_第2页
第2页 / 共4页
ASTM_A_474_-_03_2013.pdf_第3页
第3页 / 共4页
ASTM_A_474_-_03_2013.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:A47403(Reapproved 2013)Standard Specification forAluminum-Coated Steel Wire Strand1This standard is issued under the fixed designation A474;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numbe

2、r in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers five grades of aluminum-coated,steel wire strand,composed of a number of round,steelwires,with aluminum coatings,for u

3、se as guys,messengers,span wires,and for similar purposes.1.2 The five grades covered are as follows:1.2.1 Utilities,1.2.2 Common,1.2.3 Siemens-Martin,1.2.4 High-Strength,and1.2.5 Extra High-Strength.1.3 Minimum breaking strengths of strand for each gradeare specified in Table 1.1.4 The values state

4、d in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2.Referenced Documents2.1 ASTM Standards:2A428/A428M Test Method for Weight Mass of Coating onAluminum-Coa

5、ted Iron or Steel Articles3.Description of Strand3.1 The designation of the finished strand shall be expressedas the nominal diameter of the strand,the number of the wiresin the strand,and the grade of the strand as prescribed in Table1.4.Ordering Information4.1 Orders for material under this specif

6、ication shall includethe following information:4.1.1 Quantity of strand in feet.4.1.2 Nominal strand diameter(size),number of wires,grade,and minimum breaking strength of strand(Section 8 andTable 1).4.1.3 Length of strand in coils or on reels(Section 19).5.Material and Manufacture5.1 The base metal

7、 shall be steel made any commerciallyaccepted steel making process and of such quality and puritythat,when drawn to the size of wire specified and coated withaluminum,the finished strand and the individual wires shall beof uniform quality and have the properties and characteristicsas prescribed in t

8、his specification.5.2 The ingot or pig aluminum used for coating shallconform to the following impurity limits:copper,maximum,%,0.10,and iron,maximum,%,0.50.6.Stranding6.1 Unless otherwise specified,3-wire strand shall have aleft lay with a uniform pitch of not less than 10 nor more than16 times the

9、 nominal diameter of the strand.Seven-wire strandshall have a left lay with a uniform pitch of not more than 16times the nominal diameter of the strand.A left lay is definedas a counter-clockwise twist away from the observer.All wiresshall be stranded with uniform tension.Stranding shall besufficien

10、tly close to ensure no appreciable reduction in diam-eter when stressed to 10%of the specified strength.6.2 All wires in the strand shall lie naturally in their truepositions in the completed strand,and when the strand is cut,the ends shall remain in position or be readily replaced by handand then r

11、emain in position.This may be accomplished by anymeans or process,such as preforming,post forming,or formsetting.7.Joints and Splices7.1 There shall be no strand joints or strand splices in anylength of the completed strand unless specifically permitted bythe purchaser.7.2 In 3-wire strand,there sha

12、ll be no joints in individualwires.In 7-wire strand,joints in individual wires shall beacceptable provided there is not more than one joint in any150-ft(46-m)section of the completed strand and the locationof each wire joint is marked on the strand with paint or someother distinguishing mark.1This s

13、pecification is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility of Subcom-mittee A05.12 on Wire Specifications.Current edition approved April 1,2013.Published April 2013.Originallyapproved in 1962.Last previous edition approved

14、in 2008 as A474 03(2008).DOI:10.1520/A0474-03R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM In

15、ternational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 7.3 Joints in the wires composing the strand shall be of theelectric-butt-welded type.Care shall be taken to prevent injuryto the wire during electric-butt-welding.All joints shall be wellmade and shall have

16、 protection from corrosion equivalent tothat of the aluminum-coated wire itself.8.Breaking Strength and Weight8.1 The minimum breaking strength of the finished strandshall be as specified in Table 1 and the approximate weight per1000 ft or 305 m of strand shall be as indicated in Table 1.8.2 A test in which the breaking strength is below theminimum specified and which may have been caused by theslipping of the specimen in the jaws of the testing machine,bybreaking within the jaws or within 1 in.

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2