收藏 分享(赏)

ASTM_A_312_-_A_312M_-_17.pdf

上传人:益****师 文档编号:186758 上传时间:2023-03-04 格式:PDF 页数:13 大小:151.84KB
下载 相关 举报
ASTM_A_312_-_A_312M_-_17.pdf_第1页
第1页 / 共13页
ASTM_A_312_-_A_312M_-_17.pdf_第2页
第2页 / 共13页
ASTM_A_312_-_A_312M_-_17.pdf_第3页
第3页 / 共13页
ASTM_A_312_-_A_312M_-_17.pdf_第4页
第4页 / 共13页
ASTM_A_312_-_A_312M_-_17.pdf_第5页
第5页 / 共13页
ASTM_A_312_-_A_312M_-_17.pdf_第6页
第6页 / 共13页
亲,该文档总共13页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:A312/A312M17Used in USDOE-NE standardsStandard Specification forSeamless,Welded,and Heavily Cold Worked AusteniticStainless Steel Pipes1This standard is issued under the fixed designation A312/A312M;the number immediately following the designation indicates the yearof original adoption o

2、r,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.

3、1 This specification2covers seamless,straight-seamwelded,and heavily cold worked welded austenitic stainlesssteel pipe intended for high-temperature and general corrosiveservice.NOTE1When the impact test criterion for a low-temperature servicewould be 15 ftlbf 20 J energy absorption or 15 mils 0.38

4、mm lateralexpansion,some of the austenitic stainless steel grades covered by thisspecification are accepted by certain pressure vessel or piping codeswithout the necessity of making the actual test.For example,GradesTP304,TP304L,and TP347 are accepted by the ASME Pressure VesselCode,Section VIII Div

5、ision 1,and by the Chemical Plant and RefineryPiping Code,ANSI B31.3,for service at temperatures as low as 425 F250 C without qualification by impact tests.Other AISI stainless steelgrades are usually accepted for service temperatures as low as 325 F200 C without impact testing.Impact testing may,un

6、der certaincircumstances,be required.For example,materials with chromium ornickel content outside the AISI ranges,and for material with carboncontent exceeding 0.10%,are required to be impact tested under the rulesof ASME Section VIII Division 1 when service temperatures are lowerthan 50 F 45 C.1.2

7、Grades TP304H,TP309H,TP309HCb,TP310H,TP310HCb,TP316H,TP321H,TP347H,and TP348H aremodifications of Grades TP304,TP309Cb,TP309S,TP310Cb,TP310S,TP316,TP321,TP347,and TP348,and are intendedfor service at temperatures where creep and stress ruptureproperties are important.1.3 Optional supplementary requi

8、rements are provided forpipe where a greater degree of testing is desired.Thesesupplementary requirements call for additional tests to be madeand,when desired,it is permitted to specify in the order one ormore of these supplementary requirements.1.4 Table X1.1 lists the standardized dimensions of we

9、ldedand seamless stainless steel pipe as shown in ANSI B36.19.These dimensions are also applicable to heavily cold workedpipe.Pipe having other dimensions is permitted to be orderedand furnished provided such pipe complies with all otherrequirements of this specification.1.5 Grades TP321 and TP321H

10、have lower strength require-ments for pipe manufactured by the seamless process innominal wall thicknesses greater than38in.9.5 mm.1.6 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.Within the text,theSI units are shown in brackets.The values stated

11、 in eachsystem may not be exact equivalents;therefore,each systemshall be used independently of the other.Combining valuesfrom the two systems may result in non-conformance with thestandard.The inch-pound units shall apply unless the“M”designation of this specification is specified in the order.NOTE

12、2The dimensionless designator NPS(nominal pipe size)hasbeen substituted in this standard for such traditional terms as“nominaldiameter,”“size,”and“nominal size.”2.Referenced Documents2.1 ASTM Standards:3A262 Practices for Detecting Susceptibility to IntergranularAttack in Austenitic Stainless Steels

13、A370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA941 Terminology Relating to Steel,Stainless Steel,RelatedAlloys,and FerroalloysA999/A999M Specification for General Requirements forAlloy and Stainless Steel PipeA1016/A1016M Specification for General Requirements forFerritic

14、Alloy Steel,Austenitic Alloy Steel,and StainlessSteel TubesE112 Test Methods for Determining Average Grain SizeE381 Method of Macroetch Testing Steel Bars,Billets,Blooms,and Forgings1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is

15、 the direct responsibility of SubcommitteeA01.10 on Stainless and Alloy Steel Tubular Products.Current edition approved March 15,2017.Published March 2017.Originallyapproved in 1948.Last previous edition approved in 2016 as A312/A312M 16a.DOI:10.1520/A0312_A0312M-17.2For ASME Boiler and Pressure Ves

16、sel Code applications see related Specifi-cation SA-312 in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis inter

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2