1、Designation:B210M12Standard Specification forAluminum and Aluminum-Alloy Drawn Seamless Tubes(Metric)1This standard is issued under the fixed designation B210M;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision
2、.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers aluminum and aluminum-al
3、loydrawn seamless tubes in straight lengths and coils for generalpurpose and pressure applications in alloys(Note 2),tempers,and thicknesses shown in Table 2.Coiled tubes are generallyavailable only as round tubes with a wall thickness notexceeding 2.00 mm and only in non heat-treatable alloys.1.2 A
4、lloy and temper designations are in accordance withANSI H35.1/H35.1M.The equivalent Unified NumberingSystem alloy designations are those of Table 1 preceded byA9,for example,A91100 for aluminum 1100 in accordance withPractice E527.NOTE1See Specification B483/B483M for aluminum and aluminum-alloy dra
5、wn tubes for general purpose applications,Specification B234Mfor aluminum-alloy drawn seamless tubes for condensers and heatexchangers,and Specification B241/B241M for aluminum-alloy seamlesspipe and seamless extruded tube.NOTE2Throughout this specification use of the term alloy in thegeneral sense
6、includes aluminum as well as aluminum alloy.1.3 This specification is the metric counterpart of Specifi-cation B210.1.4 For acceptance criteria for inclusion of new aluminumand aluminum alloys in this specification,see Annex A2.1.5 The values stated in SI units are to be regarded asstandard.No other
7、 units of measure are included in thisstandard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulat
8、ory limitations prior to use.2.Referenced Documents2.1 The following documents of the issue in effect on dateof material purchase form a part of this specification to theextent referenced herein:2.2 ASTM Standards:2B234M Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes for Condenser
9、s and Heat Ex-changers(Metric)B241/B241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded TubeB483/B483M Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General PurposeApplicationsB557M Test Methods for Tension Testing Wrought and CastAlum
10、inum-and Magnesium-Alloy Products(Metric)B660 Practices for Packaging/Packing of Aluminum andMagnesium ProductsB666/B666M Practice for Identification Marking of Alumi-num and Magnesium ProductsB807/B807M Practice for Extrusion Press Solution HeatTreatment for Aluminum AlloysB881 Terminology Relating
11、 to Aluminum-and Magnesium-Alloy ProductsB918 Practice for Heat Treatment of Wrought AluminumAlloysE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE215 Practice for Standardizi
12、ng Equipment for Electromag-netic Testing of Seamless Aluminum-Alloy TubeE527 Practice for Numbering Metals and Alloys in theUnified Numbering System(UNS)1This specification is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibility of Subcommittee B07
13、.03 onAluminum Alloy Wrought Products.Current edition approved May 15,2012.Published July 2012.Originallyapproved in 1980.Last previous edition approved in 2005 as B210M 05.DOI:10.1520/B0210M-12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at ser
14、viceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United Stat
15、es1 E607 Test Method for Atomic Emission SpectrometricAnalysis Aluminum Alloys by the Point to Plane Tech-nique Nitrogen Atmosphere(Withdrawn 2011)3E716 Practices for Sampling and Sample Preparation ofAluminum and Aluminum Alloys for Determination ofChemical Composition by Spectrochemical AnalysisE1
16、004 Test Method for Determining Electrical ConductivityUsing the Electromagnetic(Eddy-Current)MethodE1251 Test Method for Analysis of Aluminum and Alumi-num Alloys by Spark Atomic Emission Spectrometry2.3 ANSI Standards:4H35.1/H35.1M Alloy and Temper Designation Systems forAluminumH35.2M Dimensional Tolerances for Aluminum Mill Prod-ucts2.4 ASME Standard:5B 32.5 Preferred Metric Sizes For Tubular Metal ProductsOther Than Pipe2.5 Military Standard:6MIL-STD-129 Marking for Shipment and Storage2.6
