1、Designation:B56417aStandard Specification forNickel Alloy Forgings1This standard is issued under the fixed designation B564;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates t
2、he year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification2covers forgings of:Alloy TypeUNS Number(s)Fe-Ni-Cr-Mo-NN08367Low-ca
3、rbon Cr-Ni-Fe-NR20033Low-carbon Ni-Cr-MoN06035,N06058,N06059,N06044Low-carbon Ni-Cr-Mo-CuN06200Low-carbon Ni-Cr-Mo-WN06686Low-carbon Ni-Fe-Cr-Mo-CuN08031,N08034Low-carbon Ni-Mo-CrN10276,N06022,N10362Low-carbon Ni-Mo-Cr-TaN06210NiN02200Ni-Co-Cr-SiN12160Ni-Cr-Co-MoN06617Ni-Cr-FeN06600,N06603,N06690Ni-
4、Cr-Fe-AlN06025Ni-Cr-Fe-SiN06045Ni-Cr-Mo-NbN06625Ni-Cr-Mo-SiN06219Ni-Cr-Mo-WN06110Ni-Cr-W-MoN06230Ni-CuN04400Ni-Fe-CrN08120,N08800,N08810,N08811Ni-Fe-Cr-Mo-CuN08825Ni-Fe-Cr-WN06674Ni-MoN10665,N10675,N10629Ni-Mo-Cr-FeN10242,N106241.1.1 The nickel-iron-chromium alloys are UNS N08120,UNS N08800,UNS N088
5、10,and UNS N08811.Alloy UNSN08800 is normally employed in service temperatures up toand including 1100F(593C).Alloys UNS N08810,N08120,and UNS N08811 are normally employed in service tempera-tures above 1100F(593C)where resistance to creep andrupture is required,and are annealed to develop controlle
6、dgrain size for optimum properties in this temperature range.1.1.2 Nickel-iron-chromium-tungsten alloy UNS N06674 isnormally employed in service temperatures above 1100F(593C)where resistance to creep and rupture is required,andis annealed to develop optimum properties in this temperaturerange.1.2 T
7、he values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated w
8、ith its use.It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateSafety Data Sheet(SDS)for this product/material as providedby the manufacturer,to establish appropriate safety,health andenvironmental practices,and determ
9、ine the applicability ofregulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations
10、issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3B880 Specification for General Requirements for ChemicalCheck Analysis Limits for Nickel,Nickel Alloys andCobalt AlloysE8 Test Methods for Tension Testing of Metallic MaterialsE2
11、9 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE76 Test Methods for Chemical Analysis of Nickel-CopperAlloys(Withdrawn 2003)4E112 Test Methods for Determining Average Grain SizeE350 Test Methods for Chemical Analysis of Carbon Steel,Low-Alloy Steel,Si
12、licon Electrical Steel,Ingot Iron,andWrought IronE1473 Test Methods for Chemical Analysis of Nickel,Co-balt and High-Temperature Alloys1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined
13、Nickel and Cobalt and Their Alloys.Current edition approved July 1,2017.Published August 2017.Originallyapproved in 1972.Last previous edition approved in 2017 as B564 17.DOI:10.1520/B0564-17a.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SB-564 in Section II of t
14、hat Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this historical standard is
15、 referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles o
16、n standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.2 Military Standards:5MIL-STD-129 Marking for Shipment and StorageMIL-STD-271Nondestructive Testing Requirements forMetals3.Ordering Information3.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification.E
