1、Designation:A484/A484M16Standard Specification forGeneral Requirements for Stainless Steel Bars,Billets,andForgings1This standard is issued under the fixed designation A484/A484M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the ye
2、ar of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification2covers gene
3、ral requirements thatshall apply to wrought stainless steel bars,shapes,forgings,and billets or other semi-finished material(except wire)forforging,under the latest revision of each of the followingASTM specifications:A276,A314,A458,A473,A477,A479/A479M,A564/A564M,A565/A565M,A582/A582M,A638/A638M,A7
4、05/A705M,and A831/A831M.1.2 In the case of conflict between a requirement of aproduct specification and a requirement of this specification,the product specification shall prevail.In the case of conflictbetween a requirement of the product specification or arequirement of this specification and a mo
5、re stringent require-ment of the purchase order,the purchase order shall prevail.The purchase order requirements shall not take precedence ifthey,in any way,violate the requirements of the productspecification or this specification;for example,by waiving atest requirement or by making a test require
6、ment less stringent.1.3 The requirements for introduction of new materials inspecifications referencing this specification are given in AnnexA1.1.4 General requirements for flat-rolled stainless steel prod-ucts other than bar are covered in Specification A480/A480M.1.5 General requirements for wire
7、products in coils arecovered in Specification A555/A555M.1.6 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues fr
8、om the two systems may result in non-conformancewith the standard.1.7 Unless the order specifies an“M”designation,thematerial shall be furnished to inch-pound units.2.Referenced Documents2.1 ASTM Standards:3A262 Practices for Detecting Susceptibility to IntergranularAttack in Austenitic Stainless St
9、eelsA276 Specification for Stainless Steel Bars and ShapesA314 Specification for Stainless Steel Billets and Bars forForgingA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA458 Specification for Hot-Worked,Hot-Cold-Worked,andCold-Worked Alloy Steel Bars for High Strength atE
10、levated Temperatures(Withdrawn 1988)4A473 Specification for Stainless Steel ForgingsA477 Specification for Hot-Worked,Hot-Cold Worked andCold-WorkedAlloy Steel Forgings and Forging Billets forHigh Strength at Elevated Temperatures(Withdrawn1988)4A479/A479M Specification for Stainless Steel Bars andS
11、hapes for Use in Boilers and Other Pressure VesselsA480/A480M Specification for General Requirements forFlat-Rolled Stainless and Heat-Resisting Steel Plate,Sheet,and StripA555/A555M Specification for General Requirements forStainless Steel Wire and Wire RodsA564/A564M Specification for Hot-Rolled a
12、nd Cold-Finished Age-Hardening Stainless Steel Bars and ShapesA565/A565M Specification for Martensitic Stainless SteelBars for High-Temperature ServiceA582/A582M Specification for Free-Machining StainlessSteel BarsA638/A638M Specification for Precipitation Hardening IronBase Superalloy Bars,Forgings
13、,and Forging Stock for1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.17 on Flat-Rolled and Wrought Stainless Steel.Current edition approved Jan.1,2016.Published January 2016.Originall
14、yapproved in 1963.Last previous edition approved in 2015 as A484/A484M 15.DOI:10.1520/A0484_A0484M-16.2For ASME Boiler and Pressure Vessel Code Applications,see related Specifi-cation SA-484/SA-484M in Section II of that code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orconta
15、ct ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this
16、 standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 High-Temperature ServiceA700 Guide for Packaging,Marking,and Loading Methodsfor Steel Products for ShipmentA705/A705M Specification for Age-Hardening StainlessSteel ForgingsA751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel ProductsA831/A831M Specification for Austenitic and MartensiticStainless Steel Bars,Billets,and Forgings for LiquidMetal Cooled Reac
