1、Designation:B701/B701M13Standard Specification forConcentric-Lay-Stranded Self-Damping AluminumConductors,Steel Reinforced(ACSR/SD)1This standard is issued under the fixed designation B701/B701M;the number immediately following the designation indicates the yearof original adoption or,in the case of
2、 revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers concentric-lay-stranded self-damping aluminum conductor,steel-reinforced(A
3、CSR/SD),and its component wires for use as overhead electrical conduc-tors(Explanatory Notes 1 and 2).1.2 The values stated in inch-pound or SI units are to beregarded separately as standard.Each system shall be usedindependently of the other.Combining values from the twosystems may result in non-co
4、nformance with the specification.For conductor sizes designated by AWG or kcmil,the require-ments in SI units have been numerically converted fromcorresponding values stated or derived in inch-pound units.Forconductor sizes designated by SI units only,the requirementsare stated or derived in SI unit
5、s.1.2.1 For density,resistivity,and temperature,the valuesstated in SI units are to be regarded as standard.NOTE1ACSR/SD is designed to control aeolian vibration by integraldamping.The conductors consist of a central core of a round steel wire orwires surrounded by two layers of trapezoidal aluminum
6、 1350-H19 wiresor two layers of trapezoidal aluminum 1350-H19 wires and one layer ofround aluminum 1350-H19 wires(Fig.1).The trapezoidal-wire layers areseparated from each other and from the steel core by two small annulargaps that provide the conductors self-damping characteristics.The roundaluminu
7、m wires are in tight layer contact between themselves and theunderlying trapezoidal wire layer.Different strandings of the same size ofconductor are identified by type,which is the approximate ratio of steelarea to aluminum area,expressed in percent(Table 1 and Table 2).NOTE2The aluminum and temper
8、designations conform to ANSIStandard H 35.1.Aluminum 1350 corresponds to UNS A91350 inaccordance with Practice E527.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate sa
9、fety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 The following documents of the issue in effect on dateof material purchase form a part of this specification to theextent referenced herein.2.2 ASTM Standards:2B230/B230M Speci
10、fication for Aluminum 1350H19 Wirefor Electrical PurposesB232/B232M Specification for Concentric-Lay-StrandedAluminum Conductors,Coated-Steel Reinforced(ACSR)B263 Test Method for Determination of Cross-SectionalArea of Stranded ConductorsB354 Terminology Relating to Uninsulated Metallic Electri-cal
11、ConductorsB498/B498M Specification for Zinc-Coated(Galvanized)Steel Core Wire for Use in Overhead Electrical Conduc-torsB500/B500M Specification for Metallic Coated or Alumi-num Clad Stranded Steel Core for Use in OverheadElectrical ConductorsB502 Specification for Aluminum-Clad Steel Core Wire forU
12、se in Overhead Electrical Aluminum ConductorsB549 Specification for Concentric-Lay-Stranded AluminumConductors,Aluminum-Clad Steel Reinforced for Use inOverhead Electrical ConductorsB606 Specification for High-Strength Zinc-Coated(Galva-nized)Steel Core Wire for Aluminum and Aluminum-Alloy Conductor
13、s,Steel ReinforcedB802/B802M Specification for Zinc5%Aluminum-Mischmetal Alloy-Coated Steel Core Wire for AluminumConductors,Steel Reinforced(ACSR)B803 Specification for High-Strength Zinc5%Aluminum-Mischmetal Alloy-Coated Steel Core Wire for Use inOverhead Electrical ConductorsE29 Practice for Usin
14、g Significant Digits in Test Data toDetermine Conformance with SpecificationsE527 Practice for Numbering Metals and Alloys in theUnified Numbering System(UNS)1This specification is under the jurisdiction of ASTM Committee B01 onElectrical Conductors and is the direct responsibility of Subcommittee B
15、01.07 onConductors of Light Metals.Current edition approved May 1,2013.Published June 2013.Originallyapproved in 1981.Last previous edition approved in 2006 as B701/B701M 06.DOI:10.1520/B0701_B0701M-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service
16、 at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 2.3 ANSI Documents:3ANSI H35.1 American National Standard Alloy and TemperDesignation Systems for Aluminum2.4 NIST Documents:4NBS Handbook 100 Copper Wire Tables of the NationalBureau of Standards2.5 Aluminum Association Documents:5Publication 50,Code Wo
