1、Designation:A26312Standard Specification forStainless Chromium Steel-Clad Plate1This standard is issued under the fixed designation A263;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenthese
2、s indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1This specification2covers plate of a carbon steel orlow-alloy steel base t
3、o which is integrally and continuouslybonded on one or both sides a layer of stainless chromiumsteel.The material is generally intended for pressure vesseluse.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI uni
4、ts that are provided for information onlyand are not considered standard.2.Referenced Documents2.1 ASTM Standards:3A6/A6M Specification for General Requirements for RolledStructural Steel Bars,Plates,Shapes,and Sheet PilingA20/A20M Specification for General Requirements for SteelPlates for Pressure
5、VesselsA240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate,Sheet,and Strip for PressureVessels and for General ApplicationsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA480/A480M Specification for General Requirements forFlat-Rolled Stainless a
6、nd Heat-Resisting Steel Plate,Sheet,and StripA578/A578M Specification for Straight-Beam UltrasonicExamination of Rolled Steel Plates for Special Applica-tionsA751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel Products2.2 Other Standards:ASME Boiler and Pressure Vessel Code,S
7、ection IX43.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 This material is considered as single-clad or double-clad stainless chromium-steel plate,depending on whether oneor both sides are covered.3.1.2 alloy claddingthe stainless chromium steel compo-nent of the composite plat
8、e.3.1.3 base metal(backing steel)component to which thealloy cladding is applied,usually the greater percentage of thecomposite plate.3.1.4 integrally and continuously bondeda condition inwhich the alloy cladding and base metal are brought together toform a metallurgical bond at essentially the enti
9、re interface ofthe two metals by means other than those processes that do notproduce a homogeneous composite plate.4.Ordering Information4.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification.Such requirements may incl
10、ude,but are notlimited to,the following:4.1.1 Quantity(weight or number of pieces).4.1.2 Cladding alloy specification(UNS or ASTM Specifi-cation A240/A240M)and whether cladding is for corrosionallowance only.4.1.3 Base metal specification.4.1.4 Bond integrity Class(1,3,or 5;see Section 13).4.1.5 Dim
11、ensions including the minimum or nominal thick-nesses of the cladding alloy and the backing steel,or of thetotal composite and if more or less restrictive thicknesstolerances apply.4.1.6 Product analysis,if required(see Section 10).Specifywhether applicable to the cladding alloy,backing steel,or bot
12、h.4.1.7 Mechanical properties including shear test if required(see Sections 7,8,and 9).1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloysand is the direct responsibility of SubcommitteeA01.11 for Steel Plates for Boilers and Pressure Vesse
13、ls.Current edition approved Nov.1,2012.Published November 2012.Originallyapproved in 1943.Last previous edition approved in 2009 as A263 09.DOI:10.1520/A0263-12.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-263 in Section II of that Code.3For referenced ASTM st
14、andards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from American Society of Mechanical Engineers(ASME),ASMEInternational Headquar
15、ters,Two Park Ave.,New York,NY 10016-5990,http:/www.asme.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1Copyright by ASTM Intl(all rights reserved);4.1.8 Finish(see Sect
16、ion 12).4.1.9 Restrictions,if required,on repair by welding(seeSection 14).4.1.10 Additions to the specification or special requirementssuch as any applicable construction code rules.4.1.11 Notification when the cladding alloy is to be used forinclusion in the design strength calculations for an applicableconstruction code.NOTE1Construction codes may dictate certain fabrication require-ments when the cladding is used in the design calculations that may bedifferent than if the cladding is used fo
