1、Designation:B55586(Reapproved 2018)Standard Guide forMeasurement of Electrodeposited Metallic CoatingThicknesses by Dropping Test1This standard is issued under the fixed designation B555;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revisio
2、n,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide covers the use of the dropping test tomeasure the thickness of electrodeposited zinc,cadmium,coppe
3、r,and tin coatings.NOTE1Under most circumstances this method of measuring coatingthicknesses is not as reliable or as convenient to use as an appropriatecoating thickness gauge(see Test Methods B499,B504,and B568).1.2 This standard does not purport to address all of thesafety concerns,if any,associa
4、ted with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accor-dance with internationally recogniz
5、ed principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2B487 Test Method for Measure
6、ment of Metal and OxideCoating Thickness by Microscopical Examination ofCross SectionB499 Test Method for Measurement of Coating Thicknessesby the Magnetic Method:Nonmagnetic Coatings onMagnetic Basis MetalsB504 Test Method for Measurement of Thickness of Metal-lic Coatings by the Coulometric Method
7、B568 Test Method for Measurement of Coating Thicknessby X-Ray SpectrometryD1193 Specification for Reagent Water3.Summary of Guide3.1 A dropping test3consists of applying dropwise a corro-sive solution,at a constant rate,to the electroplated surface,and measuring the time required to penetrate the co
8、ating andexpose the substrate;this time is proportional to the coatingthickness.4.Significance and Use4.1 The thickness of a metal coating is often critical to itsperformance.4.2 This procedure is useful for an approximate determina-tion when the best possible accuracy is not required.For morereliab
9、le determinations,the following methods are available:Test Methods B487,B499,B504,and B568.4.3 This test assumes that the rate of dissolution of thecoating by the corrosive reagent under the specified conditionsis always the same.5.Factors Affecting the Accuracy5.1 The following factors will affect
10、the accuracy of acoating thickness measurement made by this method:5.1.1 Cleanliness of SurfaceAny foreign material on thesurface to be tested,including lacquer,grease,corrosionproducts,and conversion coatings,will interfere with the testand must be removed.Tarnish and conversion coatings canoften b
11、e removed by mild burnishing with a soft,clean pencileraser.5.1.2 Concentration of Test SolutionVariation from thestated concentrations will introduce an error unless the thick-ness factor is adjusted accordingly.Test solutions cannot bereused.5.1.3 TemperatureThe thickness factor for a givensolutio
12、n,being a function of the temperature,must be knownfor the temperature at which the test is made.Specimens to betested should be allowed to reach room temperature beforetesting.5.1.4 Dropping RateThe thickness factor is also a func-tion of the dropping rate.The thickness factors given in Section1Thi
13、s guide is under the jurisdiction of ASTM Committee B08 on Metallic andInorganic Coatings and is the direct responsibility of Subcommittee B08.10 on TestMethods.Current edition approved Aug.1,2018.Published August 20183.Originallyapproved in 1971.Last previous edition approved in 2013 as B555 86(201
14、3).DOI:10.1520/B0555-86R18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Such tests were described by Hull,R.O.
15、,and Strausser,P.,Monthly Review,American Electroplaters Society,MRAEA,Vol 22,1935,p.9,and by Brenner,A.,Proceedings,American Electroplaters Society,AEPPB,Vol 27,1939,p.204.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international
16、standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 10 are for a dropping rate of 100 drops/min and will remainvalid for the range of 95 to 105 drops/min.5.1.5 Solution DrainageThe thickness factors given inSection 10 are valid only if the test solution i
