1、Designation:A50516Standard Specification forSteel,Sheet and Strip,Alloy,Hot-Rolled and Cold-Rolled,General Requirements for1This standard is issued under the fixed designation A505;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers a g
3、roup of common require-ments that,unless otherwise specified in the materialspecification,apply to hot-rolled and cold-rolled alloy steelsheet and strip under each of the following specifications:A506,A507,and A873/A873M.1.2 In case of any conflict in requirements,the requirementsof the individual m
4、aterial specification shall prevail over thoseof this general specification.1.3 The purchaser may specify additional requirementswhich do not negate any of the provisions of this generalspecification or of the individual material specification.Suchadditional requirements,the acceptance of which are
5、subject tonegotiation with the supplier,must be included in the orderinformation(see 4.1.9).1.4 For purposes of determining conformance with thisspecification and the various material specifications referencedin 1.1,values shall be rounded to the nearest unit in theright-hand place of figures used i
6、n expressing the limitingvalues in accordance with the rounding provisions of TestMethods and Definitions A370 and Test Methods,Practices,and Terminology A751.1.5 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI uni
7、ts that are provided for information onlyand are not considered standard.2.Referenced Documents2.1 ASTM Standards:2A370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA506 Specification for Alloy and Structural Alloy Steel,Sheet and Strip,Hot-Rolled and Cold-RolledA507 Specifica
8、tion for DrawingAlloy Steel,Sheet and Strip,Hot-Rolled and Cold-RolledA700 Guide for Packaging,Marking,and Loading Methodsfor Steel Products for ShipmentA751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel ProductsA873/A873M Specification for Steel Sheet and Strip,Chromium-Mol
9、ybdenum Alloy,for Pressure Vessels(Withdrawn 1997)3A919 Terminology Relating to Heat Treatment of Metals(Withdrawn 1999)3A1073/A1073M Practice for Using Hand Micrometers toMeasure the Thickness of Nonmetallic and Metallic-Coated Steel Sheet2.2 Federal Standard:4Fed.Std.No.123 Marking for Shipment(Ci
10、vil Agencies)2.3 Military Standard:4MIL-STD-129 Marking for Shipment and Storage3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 sheet and strip,nhot-rolled and cold-rolled alloysteel sheet and strip is classified as shown in Table 1(a)andTable 1(b).3.1.2 exclusive,adjwhen used
11、in relation to ranges,as forranges of thicknesses in the tables of permissible variations indimensions,the term“exclusive”is intended to exclude onlythe greater value of the range.Thus a range from 60 to 72 in.(1524 to 1829 mm)exclusive includes 60 in.but does notinclude 72 in.3.1.3 manufacturer(mat
12、erial manufacturer),nan organi-zation that performs or directly controls one or moreoperations,such as melting,rolling,coiling,and heat1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloysand is the direct responsibility of SubcommitteeA01.19
13、 on Steel Sheet and Strip.Current edition approved March 1,2016.Published March 2016.Originallyapproved in 1964.Last previous edition approved in 2012 as A505 12.DOI:10.1520/A0505-16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org
14、.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,
15、PA 19111-5094,Attn:NPODS.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 treatment,that affects the chemical composition or mechanicalproperties of the material.4.Ordering I
16、nformation4.1 Orders shall include the following information,asnecessary,to describe adequately the desired material:4.1.1 Specification designation,including year of issue,4.1.2 Chemical composition(grade),4.1.3 Classification of the material(that is,hot-rolled sheet),4.1.4 Dimensions(thickness,width,length)in decimalinches,4.1.5 Quantity(weight or number of pieces),4.1.6 Condition(that is,“hot-rolled,”“cold-rolled”),4.1.7 Heat treatment required,if any,4.1.8 Type of edge,4.1.9 Additional infor
