1、Designation:A36/A36M14Standard Specification forCarbon Structural Steel1This standard is issued under the fixed designation A36/A36M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses in
2、dicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification2covers carbon steel shapes,plates,and bars of structural
3、quality for use in riveted,bolted,orwelded construction of bridges and buildings,and for generalstructural purposes.1.2 Supplementary requirements are provided for use whereadditional testing or additional restrictions are required by thepurchaser.Such requirements apply only when specified in thepu
4、rchase order.1.3 When the steel is to be welded,a welding proceduresuitable for the grade of steel and intended use or service is tobe utilized.See Appendix X3 of Specification A6/A6M forinformation on weldability.1.4 The values stated in either inch-pound units or SI unitsare to be regarded separat
5、ely as standard.Within the text,theSI units are shown in brackets.The values stated in eachsystem are not exact equivalents;therefore,each system is tobe used independently of the other,without combining valuesin any way.1.5 The text of this specification contains notes or footnotes,or both,that pro
6、vide explanatory material.Such notes andfootnotes,excluding those in tables and figures,do not containany mandatory requirements.1.6 For structural products produced from coil and fur-nished without heat treatment or with stress relieving only,theadditional requirements,including additional testing
7、require-ments and the reporting of additional test results,of A6/A6Mapply.2.Referenced Documents2.1 ASTM Standards:3A6/A6M Specification for General Requirements for RolledStructural Steel Bars,Plates,Shapes,and Sheet PilingA27/A27M Specification for Steel Castings,Carbon,forGeneral ApplicationA307
8、Specification for Carbon Steel Bolts,Studs,andThreaded Rod 60 000 PSI Tensile StrengthA325 Specification for Structural Bolts,Steel,Heat Treated,120/105 ksi Minimum Tensile StrengthA325M Specification for Structural Bolts,Steel,HeatTreated 830 MPa Minimum Tensile Strength(Metric)A500 Specification f
9、or Cold-Formed Welded and SeamlessCarbon Steel Structural Tubing in Rounds and ShapesA501 Specification for Hot-Formed Welded and SeamlessCarbon Steel Structural TubingA502 Specification for Rivets,Steel,StructuralA563 Specification for Carbon and Alloy Steel NutsA563M Specification for Carbon andAl
10、loy Steel Nuts(Met-ric)A668/A668M Specification for Steel Forgings,Carbon andAlloy,for General Industrial UseA1011/A1011M Specification for Steel,Sheet and Strip,Hot-Rolled,Carbon,Structural,High-Strength Low-Alloy,High-StrengthLow-AlloywithImprovedFormability,and Ultra-High StrengthA1018/A1018M Spe
11、cification for Steel,Sheet and Strip,Heavy-ThicknessCoils,Hot-Rolled,Carbon,Commercial,Drawing,Structural,High-Strength Low-Alloy,High-StrengthLow-AlloywithImprovedFormability,and Ultra-High StrengthF568M Specification for Carbon and Alloy Steel Externally1This specification is under the jurisdictio
12、n of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.02 on Structural Steel for Bridges,Buildings,Rolling Stock and Ships.Current edition approved Dec.1,2014.Published December 2014.Originallyapproved in 1960.Last previous edition ap
13、proved in 2012 as A36/A36M 12.DOI:10.1520/A0036_A0036M-14.2For ASME Boiler and Pressure Vessel Code Applications,see related Specifi-cations SA-36 in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annu
14、al Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1Copyright by ASTM
15、Intl(all rights reserved);Threaded Metric Fasteners(Metric)(Withdrawn 2012)4F1554 Specification for Anchor Bolts,Steel,36,55,and105-ksi Yield Strength3.Appurtenant Materials3.1 When components of a steel structure are identified withthis ASTM designation but the product form is not listed in thescop
16、e of this specification,the material shall conform to one ofthe standards listed in Table 1 unless otherwise specified by thepurchaser.4.General Requirements for Delivery4.1 Structural products furnished under this specificationshall conform to the requirements of the current edition ofSpecification A6/A6M,for the specific structural productordered,unless a conflict exists in which case this specificationshall prevail.4.2 Coils are excluded from qualification to this specifica-tion until they ar
