1、Designation:F100112(Reapproved 2017)Standard Guide forSelection of Chemicals to Evaluate Protective ClothingMaterials1This standard is issued under the fixed designation F1001;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year
2、of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONWorkers involved in the production,use,and transportation of chemicals can be exposed tonumerous compounds capable of c
3、ausing harm upon contact with the human body.The deleteriouseffects of these chemicals can range from acute trauma,such as dermatitis or burns,to chronicdegenerative disease,such as cancer or pulmonary fibrosis.Because engineering controls may noteliminate all possible exposures,attention is often g
4、iven to reducing the potential for direct skincontact through the use of protective clothing that resists degradation,penetration,and permeation.Standard test methods are being established to measure degradation,penetration,and permeationchemical resistance of protective clothing materials.Chemical
5、resistance information for a number ofchemicals often accompanies many protective clothing articles.However,because there are so manypossible protective clothing and chemical combinations,the number and type of chemicals appearingin chemical resistance tables vary extensively.This guide establishes
6、a standardized list of chemicals to be used in evaluating protective clothingmaterials.The list of chemicals includes a broad range of representative chemical classes andproperties.This guide is intended to provide a minimum set of chemicals in generating test results forprotective clothing users an
7、d to aid in screening new materials.1.Scope1.1 The purpose of this guide is to provide a recommendedlist of both liquid and gaseous chemicals for evaluatingprotective clothing materials in testing programs.1.2 Results derived from testing programs using these listsof test chemicals are not intended
8、for the definitive character-ization of protective clothing materials.1.3 This list of test chemicals is not inclusive of all chemicalchallenges;the chemicals were chosen to represent broadranges of liquid and gaseous chemical classes and properties.Not all chemical classes are represented.Other che
9、micals,especially those of interest to the manufacturer or user,shouldbe tested in addition to those recommended in this guide.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appr
10、o-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.A specific hazardsstatement is given in Section 7.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in th
11、e Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2F739 Test Method for Permeation of Liquids and Gasesthrough Protective Clothing
12、 Materials under Conditions ofContinuous ContactF903 Test Method for Resistance of Materials Used inProtective Clothing to Penetration by LiquidsF1052 Test Method for Pressure Testing Vapor ProtectiveSuitsF1494 Terminology Relating to Protective Clothing1This guide is under the jurisdiction of ASTM
13、Committee F23 on PersonalProtective Clothing and Equipment and is the direct responsibility of SubcommitteeF23.30 on Chemicals.Current edition approved June 1,2017.Published June 2017.Originallyapproved in 1989.Last previous edition approved in 2012 as F1001 12.DOI:10.1520/F1001-12R17.2For reference
14、d ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken
15、,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization
16、Technical Barriers to Trade(TBT)Committee.1 F2588 Test Method for Man-In-Simulant Test(MIST)forProtective Ensembles2.2 OSHA Standards:329 CFR 1910.1047 Ethylene Oxide29 CFR 1910.1051 1,3-Butadiene29 CFR 1910.1052 Dichloromethane2.3 Other Standards:Compressed GasAssociation Publication P-1 Safe Handlingof Compressed Gases in Containers43.Terminology3.1 Definitions:3.1.1 degradation,nthe deleterious change in one or moreproperties of a material.3.1.2 penetration,nfor chemical protective clothing,t
