收藏 分享(赏)

ASTM_F_1055_-_16a.pdf

上传人:益****师 文档编号:187909 上传时间:2023-03-04 格式:PDF 页数:14 大小:578.82KB
下载 相关 举报
ASTM_F_1055_-_16a.pdf_第1页
第1页 / 共14页
ASTM_F_1055_-_16a.pdf_第2页
第2页 / 共14页
ASTM_F_1055_-_16a.pdf_第3页
第3页 / 共14页
ASTM_F_1055_-_16a.pdf_第4页
第4页 / 共14页
ASTM_F_1055_-_16a.pdf_第5页
第5页 / 共14页
ASTM_F_1055_-_16a.pdf_第6页
第6页 / 共14页
亲,该文档总共14页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:F105516aStandard Specification forElectrofusion Type Polyethylene Fittings for OutsideDiameter Controlled Polyethylene and CrosslinkedPolyethylene(PEX)Pipe and Tubing1This standard is issued under the fixed designation F1055;the number immediately following the designation indicates the

2、year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers electrofusion polyethylene fit-t

3、ings for use with outside diameter-controlled polyethylenepipe,covered by Specifications D2513,D2737,D3035,F714,F2623,F2769 and crosslinked polyethylene(PEX),covered bySpecifications F876 and F2788/F2788M.Requirements formaterials,workmanship,and testing performance are included.All requirements for

4、 joining PE electrofusion fittings to PEpipe shall also apply to joining PE electrofusion fittings to PEXpipe.Where applicable in this specification“pipe”shall mean“pipe”or“tubing.”1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematica

5、lconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following safety hazards caveat pertains only to thetest method portion,Section 9,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with it

6、s use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D638 Test Method for Tensile Properties of PlasticsD1598 Test Method for Ti

7、me-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2513 Specification for Polyethylene(PE)Gas PressurePipe,Tubing,and FittingsD27

8、37 Specification for Polyethylene(PE)Plastic TubingD3035 Specification for Polyethylene(PE)Plastic Pipe(DR-PR)Based on Controlled Outside DiameterD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsF412 Terminology Relating to Plastic Piping SystemsF714 Specification for Polyet

9、hylene(PE)Plastic Pipe(DR-PR)Based on Outside DiameterF876 Specification for Crosslinked Polyethylene(PEX)Tub-ingF905 Practice for Qualification of Polyethylene Saddle-Fused JointsF1473 Test Method for Notch Tensile Test to Measure theResistance to Slow Crack Growth of Polyethylene Pipesand ResinsF2

10、623 Specification for Polyethylene of Raised Temperature(PE-RT)SDR 9 TubingF2788/F2788M Specification for Metric and Inch-sizedCrosslinked Polyethylene(PEX)PipeF2769 Specification for Polyethylene of Raised Temperature(PE-RT)Plastic Hot and Cold-Water Tubing and Distri-bution Systems2.2PPI Standards

11、:3PPI TR-3 Policies and Procedures for Developing Hydro-static Design Basis(HDB),Pressure Design Basis(PDB),Strength Design Basis(SDB),and Minimum RequiredStrength(MRS)Rating for Thermoplastic Piping Materi-als or PipePPI TR-4 HDB/SDB/PDB/MRS Listed Materials,PPI List-ing of Hydrostatic Design Basis

12、(HDB),Strength DesignBasis(SDB),and Minimum Required Strength(MRS)Rating for Thermoplastic Piping Materials or Pipe1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved

13、 Nov.15,2016.Published January 2017.Originallyapproved in 1987.Last previous edition approved in 2016 as F1055 16.DOI:10.1520/F1055-16A.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume inform

14、ation,refer to the standards Document Summary page onthe ASTM website.3Available from Plastics Pipe Institute(PPI),105 Decker Court,Suite 825,Irving,TX 75062,http:/www.plasticpipe.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,

15、PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by

16、the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.3 ISO Standards:4ISO 13954 Plastics pipe and fittings Peel decohesion testfor polyethylene(PE)electrofusion assemblies of nominaldiameter greater than or equal to 90 mm3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412,and abbreviations are in accordance with Termi-nology D1600,unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.2.1 electrofusiona heat fusion joini

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2