1、Designation:F106987(Reapproved 2012)An American National StandardStandard Specification forDoors,Watertight,Gastight/Airtight and Weathertight,Individually Dogged,for Marine Use1This standard is issued under the fixed designation F1069;the number immediately following the designation indicates the y
2、ear oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification,to be used in conjunction withSpecificati
3、on F1073,covers the principal dimensions and themechanical requirements for manufacturing steel,aluminum,and glass-reinforced plastic,individually dogged,watertight,gastight/airtight,and weathertight doors,for personnel accessthrough bulkheads,complete with frames,for marine useintended to maintain
4、the structural and tightness integrity ofbulkheads.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.3 The following safety hazards caveat pertains to the testmethod portion,Section 8,of this specification:This stand
5、arddoes not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2.Referenced Documents2.1 ASTM Stand
6、ards:2A36/A36M Specification for Carbon Structural SteelA131/A131M Specification for Structural Steel for ShipsB209 Specification for Aluminum and Aluminum-AlloySheet and PlateF1073 Specification for Door Fittings,for Watertight/Gastight/Airtight,Weathertight,and Non-Tight Doors,for Marine Use2.2 AB
7、S Standard:3Rules for Building and Classing Steel Vessels2.3 Military Standards:4MIL-R-900 Rubber Gasket Material(45 Durometer Hard-ness)MIL-R-21607 Resins,Polyester Low-Pressure LaminatingFire RetardantMIL-P-17549 Plastic Laminates,Fibrous Glass ReinforcedMIL-G-17927 Gaskets,Glass-Metallic Cover,Si
8、licone CoreMIL-C-81706 Coating,Aluminum and Aluminum AlloysMIL-P-24441 Epoxy-Polyamide PaintDoD-STD-2138 Metal Sprayed Coating Systems for Corro-sion ProtectionTT-E-490 Enamel Silicone Alkyd Copolymer,Semi-glossExterior3.Classification3.1 The doors shall be classified into groups as given inTable 1,
9、according to their application;in addition,the length“L”shall be in accordance with the ABS Rules for Buildingand Classing Steel Vessels.3.2 The doors shall be of two types.Type I doors shallconform to all dimensions,scantlings,and details of thisspecification.Type II doors shall be to special openi
10、ngsconforming to the test methods of this specification andscantlings indicated in Figs.1-4.Special built doors with morethan 9 psi(62 kPa)shall be indicated in the ordering informa-tion(see Supplementary Requirements).3.2.1 Tolerances of all doors shall be 618in.(3 mm).3.3 Where structural fire pro
11、tection requirements areapplicable,the doors shall meet the same requirements asrequired for the bulkheads in which fitted.4.Ordering Information4.1 Orders for doors,under this specification,shall includethe following:4.1.1 Group(see Table 1),type of material and dimensions(see Tables 2-5 inclusive)
12、of doors,4.1.2 Nominal and ASTM designations indicating fixedlights or no lights,4.1.3 Quantity of each hand of door(right hand/left hand),1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfi
13、tting and Deck Machinery.Current edition approved April 1,2012.Published November 2012.Originallyapproved in 1987.Last previous edition approved in 2004 as F1069 87(2004).DOI:10.1520/F1069-87R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at ser
14、viceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Bureau of Shipping(ABS),ABS Plaza,16855Northchase Dr.,Houston,TX 77060.4Available from Standardization Documents Order Desk,Bldg.4 Section D,700Ro
15、bbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.1.4 Test head to be indicated when Type II door isrequired,and4.1.5 Hasp and staple assemblies.4.2 Inspection and acceptance of doors shall
16、 be agreed uponbetween the purchaser and the supplier.5.Materials and Manufacture5.1 The materials and specifications shall be as shown inTable 5.5.2 Glass-reinforced plastic(GRP)material of doors andframes shall meet the requirements of MIL-P-17549,Grade 1.In addition,laminate must have the flammability limits equal tothe requirements for Grade 2,Class A,of MIL-R-21607.5.2.1 All GRP material that is drilled,cut,and sanded,leaving the surface exposed,shall be sealed with the same resinas the exp
