1、Designation:F101402(Reapproved 2012)1An American National StandardStandard Specification forFlashlights on Vessels1This standard is issued under the fixed designation F1014;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of
2、last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1NOTEReapproved with editorial changes in October 201
3、2.1.Scope1.1 This specification covers three types of flashlights(seeSection 4).1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.3 The following precautionary caveat pertains only to thetest method portion,Section 9
4、,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2
5、.Referenced Documents2.1 Military Standard:2MIL-STD-105D Sampling Procedures and Tables for In-spection by Attributes2.2 UL Standard:3UL Standard No.783 Standard for Safety Electric Flash-lights and Lanterns for Use in Hazardous(Classified)Locations3.Terminology3.1 Definitions of Terms Specific to T
6、his Standard:3.1.1 lota manufacturers production run for a specific typeof flashlight.3.1.2 order batchthe size of a specific contract or pur-chase order taken from the lot.3.1.3 production testingthe testing performed during a lotrun of specific flashlights.4.Classification4.1 The three types of fl
7、ashlights covered in this specifica-tion are classified as follows:4.1.1 Type IFlashlights for use in lifeboats and liferafts.4.1.2 Type IIFlashlights for use in hazardous locationswhere fire or explosion hazards may exist due to the presenceof flammable gases or vapors,flammable liquids,combustible
8、dust,or ignitable fibers or flyings.4.1.3 Type IIIFlashlights for use in lifeboats and liferaftsand suitable for hazardous locations.4.2 Type I flashlights shall be manufactured in accordancewith Sections 2-11.Type II flashlights shall meet the require-ments in Sections 11 and 12.Type III flashlight
9、s shall meet therequirements in Sections 2-12.5.Materials and Manufacture5.1 MaterialsAll materials used in the construction ofthese flashlights shall be of a quality suitable for the purposeintended and shall conform to the requirements of this speci-fication.5.2 ManufacturePlastic,when used,shall
10、be a suitablethermoplastic or thermosetting material so molded as toproduce a dense solid structure,uniform in texture,finish,andmechanical properties.6.General Requirements6.1 Each flashlight shall be a three-cell light.6.2 Each flashlight shall provide a concentrated beam oflight.When used in this
11、 specification,a concentrated beam oflight is light projected in a nearly parallel beam and is used toilluminate objects at considerable distances.6.3 The flashlight shall show no leakage of water and shallbe in perfect working order following the test prescribed in 9.2.6.4 The proportions and desig
12、n of each flashlight shall besuch that the assembled unit complete with lamp and cells shallbe capable of withstanding,without breakage or material1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.10
13、 onElectrical.Current edition approved Oct.1,2012.Published November 2012.Originallyapproved in 1986.Last previous edition approved in 2007 as F1014-02(2007).DOI:10.1520/F1014-02R12E01.2Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5098,At
14、tn:NPODS.3Available from Underwriters Laboratories(UL),333 Pfingsten Rd.,Northbrook,IL 60062-2096,http:/.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 distortion of any part and without upsetting the lamp focus,thetest specified in 9.6.
15、Damage of lamp filament or shifting offilament within the lamp as a result of this test shall not because for rejection of the flashlight if the flashlight operateswhen the spare lamp is used.6.5 Each flashlight must be furnished with two lamps.Oneof these lamps is a spare and must be contained with
16、in the bodyof the flashlight,either in the end cap or reflector head area.6.6 All metal parts of each flashlight shall be made ofcorrosion-resistant material.All copper or copper-alloy partscoming in contact with rubber shall not corrode or disintegratethe rubber.6.7 The construction of each flashlight shall be such that ametallic contact outside the case cannot close the battery circuitand cause the light to come on.6.8 Each flashlight shall be provided with means to preventit from rolling.7.Ph
