1、Designation:F120311An American National StandardStandard Specification forWashing MachinesPot,Pan,and Utensil,Heat Sanitizing,Commercial Rotary Conveyor Type1This standard is issued under the fixed designation F1203;the number immediately following the designation indicates the year oforiginal adopt
2、ion or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers manually fed,motor-drivenrotary conveyor type,automati
3、cally controlled,commercialpot,pan,and utensil washing machines,hereinafter referred toas“the washer.”1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not cons
4、idered standard.1.3 The following precautionary statement pertains only tothe test methods portion,Section 9 of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appr
5、opriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2A53/A53M Specification for Pipe,Steel,Black and Hot-Dipped,Zinc-Coated,Welded and SeamlessA167 Specification for Stainless and Heat-ResistingChromium-N
6、ickel Steel Plate,Sheet,and StripA436 Specification for Austenitic Gray Iron CastingsA554 Specification for Welded Stainless Steel MechanicalTubingB43 Specification for Seamless Red Brass Pipe,StandardSizesB75 Specification for Seamless Copper TubeB127 Specification for Nickel-Copper Alloy(UNS N0440
7、0)Plate,Sheet,and StripD3951 Practice for Commercial PackagingF760 Specification for Food Service Equipment ManualsF1021 Specification for Feeders,Detergent,Rinse Agent,and Sanitizing Agent for Commercial Dishwashing andGlasswashing Machines2.2 American National Standards:3ANSI SI.4 Specification fo
8、r Sound Level MetersANSI SI.13 Methods for the Measurement of Sound Pres-sure Levels2.3 Federal Regulations:4OSHA Title 292.4 National Electrical Manufacturers Association Stan-dards:5NEMA ICS Industrial Controls and SystemsNEMA MG-I Motors and Generators2.5 National Fire Protection Association Stan
9、dard:6NFPA/ANSI 70 National Electrical Code2.6 NSF International Standards:7NSF/ANSI 3 Commercial Warewashing EquipmentNSF/ANSI 5 Commercial Hot Water Generating EquipmentNSF/ANSI 29 Detergent/Chemical Feeders for CommercialSpray-Type Dishwashing MachinesNSF ListingsFood Equipment2.7 Underwriters La
10、boratories Standard:8UL 921 Commercial Dishwashers3.Terminology3.1 Definitions:3.1.1 commercial pot,pan,and utensil washing machinesmachines that uniformly wash,rinse and heat sanitize foodpreparation utensils.The machines shall be capable of remov-ing physical soil and sanitizing properly racked an
11、d pre-scraped multiple pots,pans,and utensils.The machines shall1This specification is under the jurisdiction of ASTM Committee F26 on FoodService Equipment and is the direct responsibility of Subcommittee F26.01 onCleaning and Sanitation Equipment.Current edition approved Dec.1,2011.Published Janua
12、ry 2012.Originallyapproved in 1988.Last previous edition approved in 2006 as F1203 06.DOI:10.1520/F1203-11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards
13、Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036.4Available from Standardization Documents Order Desk,DODSSP,Bldg.4,Section D,700 Robbins Ave.,Philadelphia,PA 19111-5098.5Available from National Electrical
14、Manufacturers Association(NEMA),1300N.17th St.,Suite 1847,Rosslyn,VA 22209.6Available from National Fire Protection Association(NFPA),1 BatterymarchPark,Quincy,MA 02269-9101.7Available from NSF International,P.O.Box 130140,789 N.Dixboro Rd.,AnnArbor,MI 48113-0140.8Available from Underwriters Laborat
15、ories(UL),333 Pfingsten Rd.,Northbrook,IL 60062.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 consist of the following principal parts:legs,wash chamber,hood,tank,doors,spray assemblies,pumps,motors,controls,piping,valves,heating equipm
16、ent and accessories.4.Classification4.1 GeneralThe washer shall be of the following type,size,and class as specified.4.2 Types:4.2.1 Motor-Driven Continuous Rotary Conveyor:4.2.1.1 Type IOne door(front loading).4.2.1.2 Type IIOne or two door(pass-through corneroperation).4.2.1.3 Type IIIOne or two door(pass-through straightline operation).4.2.1.4 Size 1Nominal 42-in.diameter.4.2.1.5 Size 2Nominal 60-in.diameter.4.2.1.6 Size 3Nominal 74-in.diameter.4.2.1.7 Size 4Nominal 86-in.diameter.4.3 Tank He
