1、Designation:F108318Standard Specification forPipe,Steel,Hot-Dipped Zinc-Coated(Galvanized)Welded,for Fence Structures1This standard is issued under the fixed designation F1083;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year
2、of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers hot-dippe
3、d galvanized weldedsteel pipe in sizes ranging from 1.3158.625 in.(33.4219.1 mm)outside diameter(OD)inclusive,with nominal(average)wall thickness as given in Table 1 and Table 2.Pipehaving other dimensions(Note 2)may be furnished providedsuch pipe complies with all other requirements of this specifi
4、-cation.Pipe ordered under this specification is intended for useas a structural support for fencing in accordance with Specifi-cation F1043,Group 1A.NOTE1Outside diameter size is designated in that fence fittings aredesigned to securely fit on the outside of the pipe framework.NOTE2A comprehensive
5、listing of standardized pipe dimensions iscontained in ANSI B 36.10.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.1.3 This international standard was developed in accor-dance with internationally recognized princip
6、les on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight Mass o
7、f Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA700 Guide for Packaging,Marking,and Loading Methodsfor Steel Products for ShipmentB6 Specification for ZincE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDeter
8、mine Conformance with SpecificationsF1043 Specification for Strength and Protective Coatings onSteel Industrial Fence Framework2.2 ANSI Standard:B 36.10 Welded and Seamless Wrought Steel Pipe33.Ordering Information3.1 Orders for material under this specification shall includethe following as require
9、d,to describe the desired materialadequately:3.1.1 Specification designation,3.1.2 Quantity(feet,metres,or number of lengths),3.1.3 Name of material(schedule 40 steel pipe or schedule80 steel pipe),3.1.4 Method of manufacture(electric-resistance welded orfurnace welded),3.1.5 Grade(Regular or High S
10、trength)High StrengthGrade available in sizes 1.660 in.(42.2 mm)OD and larger.Regular Grade is available for all sizes.3.1.6 Type(Table 1 or Table 2),3.1.7 Size(outside diameter and weight per foot),3.1.8 Length(see Section 14),3.1.9 Certification(see 18.1),and3.1.10 Selection of applicable level of
11、 preservation andpackaging required,if other than in accordance with PracticesA700(see 20.1).4.Process4.1 The steel for welded pipe shall be made by one or moreof the following processes:electric-furnace,open hearth,orbasic-oxygen.The steel for welded pipe shall be of softweldable quality.4.2 Welded
12、 pipe 4.500 in.(114.3 mm)OD and under may bebutt-welded,unless otherwise specified.Welded pipe over4.500 in.(114.3 mm)OD shall be electric-welded.1This specification is under the jurisdiction of Committee F14 on Fences and isthe direct responsibility of Subcommittee F14.40 on Chain Link Fence and Wi
13、reAccessories.Current edition approved April 1,2018.Published April 2018.Originallyapproved in 1987.Last previous edition approved in 2016 as F1083 16.DOI:10.1520/F1083-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual
14、 Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Consh
15、ohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organi
16、zation Technical Barriers to Trade(TBT)Committee.1 5.Coating5.1 Pipe shall be coated with zinc inside and outside by thehot-dip process.5.2 The zinc used for the coating shall be any grade of zincconforming to Specification B6.6.Tensile Requirements6.1 Pipe furnished to this specification shall meet thefollowing minimum tensile requirements when tested in accor-dance with Test Methods E8/E8M.6.1.1 Tensile Strength:6.1.1.1 Regular GradeMinimum tensile strength shall be48 000 psi(330 MPa).6.1.1.2
