1、Designation:F1430/F1430M18Standard Test Method forAcoustic Emission Testing of Insulated and Non-InsulatedAerial Personnel Devices with Supplemental Load HandlingAttachments1This standard is issued under the fixed designation F1430/F1430M;the number immediately following the designation indicates th
2、e yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method describes a procedure for acousticemiss
3、ion(AE)testing of aerial personnel devices(APDs)withsupplemental load handling attachments.1.1.1 Equipment CoveredThis test method covers thefollowing types of vehicle-mounted aerial personnel deviceswith supplemental load handling attachments:1.1.1.1 Extensible-boom APDs,1.1.1.2 Articulating-boom A
4、PDs,and1.1.1.3 Any combination of 1.1.1.1 and 1.1.1.2.1.1.2 Equipment Not CoveredThis test method does notcover any of the following equipment:1.1.2.1 Aerial personnel devices without supplemental loadhandling attachments,1.1.2.2 Digger-derricks with platform,1.1.2.3 Cranes with platform,and1.1.2.4
5、Aerial devices with load-lifting capabilities locatedanywhere other than adjacent to the platform.NOTE1This test method is not intended to be a stand-alone NDTmethod for the verification of the structural integrity of an aerial device.Other NDT methods should be used to supplement the results.1.2 Th
6、e AE test method is used to detect and area-locateemission sources.Verification of emission sources may requirethe use of other nondestructive test(NDT)methods,such asradiography,ultrasonics,magnetic particle,liquid penetrant,and visual inspection.(WarningThis test method requiresthat external loads
7、 be applied to the superstructure of thevehicle under test.During the test,caution must be taken tosafeguard personnel and equipment against unexpected failureor instability of the vehicle or components.)1.3 The values stated in either SI units or inch-pound unitsare to be regarded separately as sta
8、ndard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associat
9、ed with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognize
10、d principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2E94 Guide for Radiographic Ex
11、amination Using IndustrialRadiographic FilmE114 Practice for Ultrasonic Pulse-Echo Straight-BeamContact TestingE164 Practice for Contact Ultrasonic Testing of WeldmentsE569 Practice for Acoustic Emission Monitoring of Struc-tures During Controlled StimulationE650 Guide for Mounting Piezoelectric Aco
12、ustic EmissionSensorsE750 Practice for Characterizing Acoustic Emission Instru-mentationE976 Guide for Determining the Reproducibility ofAcousticEmission Sensor ResponseE1316 Terminology for Nondestructive ExaminationsE1417/E1417M Practice for Liquid Penetrant TestingE1444/E1444M Practice for Magnet
13、ic Particle TestingF914 Test Method for Acoustic Emission for Insulated andNon-Insulated Aerial Personnel Devices Without Supple-mental Load Handling Attachments1This test method is under the jurisdiction of ASTM Committee F18 onElectrical Protective Equipment for Workers and is the direct responsib
14、ility ofSubcommittee F18.55 on Inspection and Non-Destructive Test Methods for AerialDevices.Current edition approved March 1,2018.Published April 2018.Originallyapproved in 1992.Last previous edition approved in 2015 as F1430/F1430M15.DOI:10.1520/F1430_F1430M-18.2For referenced ASTM standards,visit
15、 the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United
16、StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 F2174 Practice for Verifying Acoustic Emission Sensor Re-sponse2.2 Other Standards:ANSI A92.2 Standard for Vehicle-Mounted Elevating andRotating Aerial Devices3ASNT SNT-TC-1A Rec
