1、Designation:F100013(Reapproved 2019)An American National StandardStandard Practice forPiping System Drawing Symbols1This standard is issued under the fixed designation F1000;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of
2、 last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This practice establishes piping syst
3、em drawing sym-bols for marine use.1.2 This set of standard symbols is intended for use onpiping system diagrammatics and arrangements for ships.1.3 Where graphical symbols are required for an item orequipment not covered by this practice,the form and characterof the symbol will be left to the discr
4、etion of the activityconcerned,provided that the symbol used does not duplicateany of those contained herein,and is clearly understandable,subject to one interpretation only,or explained by a suitablenote on the drawing when necessary.1.4 Since symbolic representation does not usually involveexact o
5、r scale layout or the actual run or leads of piping,thesame symbol may be used for all projections of the system(plan,elevations,and sections).1.5 Symbols for fluid power,heating,ventilation,and airconditioning(HVAC),and Navy damage control diagrams arenot included in this practice.1.6 This internat
6、ional standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committ
7、ee.2.Significance and Use2.1 Figure 1 provides symbols for strainers,separators,andfilters.2.2 Figure 2 provides symbols for valves.Valves are cat-egorized under the following headings:globe,angle,check,ball,butterfly,gate,relief,manifolds,control,noise control,and miscellaneous.2.3 Figure 3 provide
8、s symbols for valve appendages such asactuators and locking devices.Symbols shown on Fig.3 are tobe combined with the appropriate symbol from Fig.2.2.4 Figure 4 provides symbols for piping systemrelatedinstrumentation.These symbols are categorized under thefollowing headings:pressure,temperature,flo
9、w,level,switches,alarms,and miscellaneous.2.5 Figure 5 provides symbols for fans,pumps,and tur-bines.2.6 Figure 6 provides symbols for plumbing components.2.7 Figure 7 provides symbols for pipe and pipe fittings.2.8 Figure 8 provides symbols for noise control componentsand designations.These symbols
10、 are generally used for sub-marine design.2.9 Figure 9 provides symbols for transitions.These sym-bols identify transitions such as pipe material or pipe schedulechanges.2.10 Figure 10 provides symbols for miscellaneous compo-nents.These are components which could not be classifiedunder the above ca
11、tegories.Examples include heat exchangers,flasks,and sea chests.2.11 Figure 11 provides symbols for grooved piping.3.Keywords3.1 drawing symbols;piping;piping drawings;piping sym-bols1This practice is under the jurisdiction of ASTM Committee F25 on Ships andMarine Technology and is the direct respon
12、sibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved May 1,2019.Published June 2019.Originallyapproved in 1986.Last previous edition approved in 2013 as F1000 13.DOI:10.1520/F1000-13R19.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocke
13、n,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization
14、 Technical Barriers to Trade(TBT)Committee.1 F1000 13(2019)2 F1000 13(2019)3 F1000 13(2019)4 F1000 13(2019)5 F1000 13(2019)6 F1000 13(2019)7 F1000 13(2019)8 F1000 13(2019)9 F1000 13(2019)10 F1000 13(2019)11 F1000 13(2019)12 F1000 13(2019)13 F1000 13(2019)14 F1000 13(2019)15 F1000 13(2019)16 F1000 13
15、(2019)17 F1000 13(2019)18 F1000 13(2019)19 F1000 13(2019)20 F1000 13(2019)21 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned inthis standard.Users of this standard are expressly advised that determination of the validit
16、y of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of th
