1、Designation:F108313Standard Specification forPipe,Steel,Hot-Dipped Zinc-Coated(Galvanized)Welded,for Fence Structures1This standard is issued under the fixed designation F1083;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year
2、of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1.Scope1.1 This specification covers hot-dipped ga
3、lvanized weldedsteel pipe in sizes ranging from 1.3158.625 in.(33.4 219.1mm)outside diameter(OD)inclusive,with nominal(average)wall thickness as given in Table 1 and Table 2.Pipe havingother dimensions(Note 2)may be furnished provided suchpipe complies with all other requirements of this specificati
4、on.Pipe ordered under this specification is intended for use as astructural support for fencing in accordance with SpecificationF1043,Group 1A.NOTE1Outside diameter size is designated in that fence fittings aredesigned to securely fit on the outside of the pipe framework.NOTE2A comprehensive listing
5、 of standardized pipe dimensions iscontained in ANSI B 36.10.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.2.Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight Mass of Coating onIron and Steel
6、Articles with Zinc or Zinc-Alloy CoatingsA700 Practices for Packaging,Marking,and Loading Meth-ods for Steel Products for ShipmentB6 Specification for ZincE8 Test Methods for Tension Testing of Metallic MaterialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Spec
7、ificationsF1043 Specification for Strength and Protective Coatings onSteel Industrial Fence Framework2.2 ANSI Standard:B 36.10 Welded and Seamless Wrought Steel Pipe33.Ordering Information3.1 Orders for material under this specification shall includethe following as required,to describe the desired
8、materialadequately:3.1.1 Specification designation,3.1.2 Quantity(feet,metres,or number of lengths),3.1.3 Name of material(schedule 40 steel pipe or schedule80 steel pipe),3.1.4 Method of manufacture(electric-resistance welded orfurnace welded),3.1.5 Grade(Regular or High Strength)High StrengthGrade
9、 available in sizes 1.660 in.(42.2 mm)OD and larger.Regular Grade is available for all sizes.3.1.6 Type(Table 1 or Table 2),3.1.7 Size(outside diameter and weight per foot),3.1.8 Length(see Section 14),3.1.9 Certification(see 18.1),and3.1.10 Selection of applicable level of preservation andpackaging
10、 required,if other than in accordance with PracticesA700(see 20.1).4.Process4.1 The steel for welded pipe shall be made by one or moreof the following processes:electric-furnace,open hearth,orbasic-oxygen.The steel for welded pipe shall be of softweldable quality.4.2 Welded pipe 4.500 in.(114.3 mm)O
11、D and under may bebutt-welded,unless otherwise specified.Welded pipe over4.500 in.(114.3 mm)OD shall be electric-welded.5.Coating5.1 Pipe shall be coated with zinc inside and outside by thehot-dip process.1This specification is under the jurisdiction of Committee F14 on Fences and isthe direct respo
12、nsibility of Subcommittee F14.40 on Chain Link Fence and WireAccessories.Current edition approved Nov.15,2013.Published November 2013.Originallyapproved in 1987.Last previous edition approved in 2010 as F1083 10.DOI:10.1520/F1083-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,
13、orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright AS
14、TM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.2 The zinc used for the coating shall be any grade of zincconforming to Specification B6.6.Tensile Requirements6.1 Pipe furnished to this specification shall meet thefollowing minimum tensile requirem
15、ents when tested in accor-dance with Test Methods E8.6.1.1 Tensile Strength:6.1.1.1 Regular GradeMinimum tensile strength shall be48 000 psi(330 MPa).6.1.1.2 High Strength Grade Sch 40Minimum tensilestrength shall be 60 000 psi(414 MPa).Available in sizes1.660 in.(42.2 mm)OD and larger.6.1.2 Yield S
16、trength:6.1.2.1 Regular GradeMinimum yield strength shall be30 000 psi(205 MPa).6.1.2.2 High Strength Grade Sch 40Minimum yieldstrength shall be 50 000 psi(344 MPa).Available in sizes1.660 in.(42.2 mm)OD and larger.7.Weight of Coating7.1 The weight of zinc coating shall be not less than 1.8oz/ft2(550 g/m2),as determined from the average results of thetwo specimens taken for test in accordance with 10.1 and notless than 1.6 oz/ft2(490 g/m2)for either of these specimens.The weight of coating expre
