1、Designation:F109887(Reapproved 2015)An American National StandardStandard Specification forEnvelope Dimensions for Butterfly ValvesNPS 2 to 241This standard is issued under the fixed designation F1098;the number immediately following the designation indicates the year oforiginal adoption or,in the c
2、ase of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification provides standard dimensions formanual(lever and gear actuator)butterfly val
3、ves installed inshipboard piping systems in NPS 2 to NPS 24,inclusive.1.2 This specification covers conventional and ANSIB16.34 class butterfly valves of both lug and wafer types.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalc
4、onversions to SI units that are provided for information onlyand are not considered standard.2.Referenced Documents2.1 ANSI Standard:2B 16.34 Small Butt Welding End Valves3.Dimensions3.1 Face-to-Face Dimensions:3.1.1 Valve body face-to-face dimensions are provided inTable 1.3.1.2 The face-to-face di
5、mensions are the metal-to-metaldimensions between the valve body flange faces that requireseparate gaskets or the compressed or installed condition forvalves using liners that extend from the body contact faces andact as flange gaskets.3.2 Actuator Dimensions:3.2.1 The maximum permissible dimensions
6、 for lever-andgear-type actuators are provided in Fig.1.3.2.2 The handwheel and handle may be on either side ofthe valve.3.2.3 All handwheels and handles rotate clockwise to closethe valve.4.Tolerances4.1 Face-to-Face DimensionsAplus or minus tolerance of116in.(1.6 mm)for all sizes shall be allowed(
7、see Table 1).5.Keywords5.1 envelope dimensions;gear actuator butterfly valves;lever butterfly valves;manual butterfly valves1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping
8、 Systems.Current edition approved May 1,2015.Published June 2015.Originallyapproved in 1987.Last previous edition approved in 2010 as F1098 87(2010).DOI:10.1520/F1098-87R15.2Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyri
9、ght ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 NOTE11 in.=25.4 mmDimensions,in.Valve SizeNPS22.53456810121416182024A8.009.0010.0010.0011.0011.0012.0014.0017.0019.0021.0023.0025.0027.00B3.003.003.503.503.504.004.004.004.00C15.0015.0015.0015.001
10、5.0015.0024.0024.0024.00E4.004.005.505.505.505.505.506.006.008.008.009.009.0010.00S12.0012.0012.0012.0012.0012.0012.0012.0012.0024.0024.0024.0024.0024.00T2.502.502.502.502.503.503.506.506.506.506.506.506.506.50U4.004.004.004.004.004.004.005.005.008.008.008.008.009.50V6.506.506.506.506.506.506.508.50
11、8.5010.5010.5011.5012.0013.50W5.005.005.005.005.005.006.007.007.509.009.0011.0011.0011.50X9.509.509.509.509.509.509.5010.5013.0013.0014.5014.5020.0020.00FIG.1 Actuator Envelope DimensionsTABLE 1 Face-to-Face DimensionsValve Size,NPSConventional,200 psig,in.(mm)ANSI B16.34,150 Class,in.(mm)2158(41)13
12、4(44)212134(44)178(48)3134(44)178(48)31211516(49)2(51)42(51)218(54)52116(52)214(57)6218(54)214(57)82716(62)212(64)102916(65)21316(71)123(76)3316(81)1431116(93)358(92)164116(103)4(102)184916(116)412(114)205116(128)5(127)24578(149)6116(154)F1098 87(2015)2 ASTM International takes no position respectin
13、g the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard
14、is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Hea
15、dquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,at the address shown below.This standa
16、rd is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple copies)of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585(phone),610-832-9555(fax),or serviceastm.org(e-mail);or through the ASTM website(www.astm.org).Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center,222Rosewood Drive,Danvers,MA 01923,Tel:(978)646-2
