1、Designation:F141209Standard Specification forPolyolefin Pipe and Fittings for Corrosive Waste DrainageSystems1This standard is issued under the fixed designation F1412;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last
2、revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers requirements for non-pressurepolyolefin pipe and fittings for corrosive waste drainagesystems.1.2 Pip
3、e is produced in Schedule 40 and 80 IPS sizes in twopolyolefins,polyethylene(PE)and polypropylene(PP).1.3 The interchangeability of pipe and fittings made bydifferent manufacturers is not addressed in this specification.Transition fittings for joining pipe and fittings of differentmanufacturers is p
4、rovided for in this specification.1.4 Pipe and fittings are joined by the heat fusion method(D2657 and F1290)or by using mechanical joints recom-mended by the manufacturer.1.5 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversi
5、ons to SI units that are provided for information onlyand are not considered standard.1.6 The following safety hazards caveat pertains only to thetest method,Section 8,of this specification.This standard doesnot purport to address all of the safety concerns,if any,associated with its use.It is the r
6、esponsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2.Referenced Documents2.1 ASTM Standards:2D543 Practices for Evaluating the Resistance of Plastics toChemical ReagentsD570 Test Method f
7、or Water Absorption of PlasticsD618 Practice for Conditioning Plastics for TestingD1248 Specification for Polyethylene Plastics ExtrusionMaterials for Wire and CableD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and Fit
8、tingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Therm
9、oplastic Pipe and Fittings by Means of aTup(Falling Weight)D2657 Practice for Heat Fusion Joining of Polyolefin Pipeand FittingsD3311 Specification for Drain,Waste,and Vent(DWV)Plastic Fittings PatternsD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsD4101 Specification for
10、Polypropylene Injection and Extru-sion MaterialsF412 Terminology Relating to Plastic Piping SystemsF1290 Practice for Electrofusion Joining Polyolefin Pipe andFittingsF1498 Specification for Taper Pipe Threads 60 for Thermo-plastic Pipe and Fittings2.2 Federal Standard:Fed.Std.No.123 Marking for Shi
11、pment(Civil Agencies)32.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage31This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved Jan.15,2009.Published January
12、2009.Originallyapproved in 1992.Last previous edition approved in 2001 as F1412 011.DOI:10.1520/F1412-09.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Do
13、cument Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/www.dodssp.daps.mil.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO
14、 Box C700,West Conshohocken,PA 19428-2959.United States1 2.4 Other Document:Uniform Plumbing Code43.Terminology3.1 Definitions:3.1.1 Definitions used in this specification are in accordancewith the definitions given in Terminology F412,and abbrevia-tions are in accordance with Terminology D1600,unle
15、ssotherwise indicated.3.1.2 The plumbing terminology used in this specification isin accordance with the definitions given in Uniform PlumbingCode,unless otherwise indicated.3.2 Definitions of Terms Specific to This Standard:3.2.1 toe-ina small reduction of the outside diameter atthe cut end of a le
16、ngth of thermoplastic pipe.4.Classification4.1 GeneralThis specification covers Schedule 40 and 80polyolefin pipe made from polyethylene or polypropylene iniron pipe sizes.4.2 This specification also includes molded fittings and inlarger sizes(8,10,12 in.)fabricated fittings.5.Materials and Manufacture5.1 Polyethylene(PE)virgin material for pipe or fittingsshall be from a single compound manufacturer and shall bemade from PE material that meets or exceeds the cell-classification requirements of
