收藏 分享(赏)

ASTM_F_15_-_04_2013.pdf

上传人:益****师 文档编号:188707 上传时间:2023-03-04 格式:PDF 页数:7 大小:245.93KB
下载 相关 举报
ASTM_F_15_-_04_2013.pdf_第1页
第1页 / 共7页
ASTM_F_15_-_04_2013.pdf_第2页
第2页 / 共7页
ASTM_F_15_-_04_2013.pdf_第3页
第3页 / 共7页
ASTM_F_15_-_04_2013.pdf_第4页
第4页 / 共7页
ASTM_F_15_-_04_2013.pdf_第5页
第5页 / 共7页
ASTM_F_15_-_04_2013.pdf_第6页
第6页 / 共7页
亲,该文档总共7页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:F1504(Reapproved 2013)Standard Specification forIron-Nickel-Cobalt Sealing Alloy1This standard is issued under the fixed designation F15;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revision.Anumber in

2、 parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers an iron-nickel-cobalt alloy,UNS K94610 containing nominally 29%nickel,17%cobalt,and 53%iron,in the forms of wire,rod,bar,st

3、rip,sheet,andtubing,intended primarily for sealing to glass in electronicapplications.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.

4、1.3 The following hazard caveat pertains only to the testmethod portion,Sections 13 and 14 of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and

5、 healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2E3 Guide for Preparation of Metallographic SpecimensE8 Test Methods for Tension Testing of Metallic MaterialsE18 Test Methods for Rockwell Hardness of Metallic Ma-terial

6、sE92 Test Method for Vickers Hardness of Metallic Materials(Withdrawn 2010)3E112 Test Methods for Determining Average Grain SizeE140 Hardness Conversion Tables for Metals RelationshipAmong Brinell Hardness,Vickers Hardness,RockwellHardness,Superficial Hardness,Knoop Hardness,andScleroscope HardnessE

7、228 Test Method for Linear Thermal Expansion of SolidMaterials With a Push-Rod DilatometerF14 Practice for Making and Testing Reference Glass-MetalBead-SealF140 Practice for Making Reference Glass-Metal Butt Sealsand Testing for Expansion Characteristics by PolarimetricMethodsF144 Practice for Makin

8、g Reference Glass-Metal SandwichSeal and Testing for Expansion Characteristics by Polari-metric Methods3.Ordering Information3.1 Orders for material under this specification shall includethe following information:3.1.1 Size,3.1.2 Temper(Section 6),3.1.3 Surface finish(Section 10),3.1.4 Marking and p

9、ackaging(Section 17),and3.1.5 Certification if required.4.Chemical Requirements4.1 The material shall conform to the requirements as tochemical composition prescribed in Table 1.5.Surface Lubricants5.1 All lubricants used during cold-working operations,such as drawing,rolling,or spinning,shall be ca

10、pable of beingremoved readily by any of the common organic degreasingsolvents.6.Temper6.1 The desired temper of the material shall be specified inthe purchase order.6.2 TubeUnless otherwise agreed upon by the supplier ormanufacturer and the purchaser,these forms shall be given afinal bright anneal b

11、y the manufacturer and supplied in theannealed temper.6.3 Strip and SheetThese forms shall be supplied in one ofthe tempers given in Table 2 or in deep-drawing temper,asspecified.6.4 Wire and Rod These forms shall be supplied in one ofthe tempers given in Table 3 as specified.Unless otherwisespecifi

12、ed,the material shall be bright annealed and supplied intemper A(annealed).1This specification is under the jurisdiction of ASTM Committee F01 onElectronics and is the direct responsibility of Subcommittee F01.03 on MetallicMaterials.Current edition approved May 1,2013.Published May 2013.Originallya

13、pproved in 1961 as F15 61T.Last previous edition approved in 2009 as F15 04(2009).DOI:10.1520/F0015-04R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards D

14、ocument Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 150FIG.1 Normal Annealed Specimen Showing No Transformation150FIG.

15、2 Partially Transformed SpecimenF15 04(2013)2 7.Grain Size7.1 Strip and sheet for deep drawing shall have an averagegrain size not larger than ASTM No.5(Note 1),and no morethan 10%of the grains shall be larger than No.5 whenmeasured in accordance with Test Methods E112.NOTE1This corresponds to a gra

16、in size of 0.065 mm,or 16 grains/in.2of image at 100 .8.Hardness8.1 Deep-Drawing TemperFor deep drawing,the hardnessshall not exceed 82 HRB for material 0.100 in.(2.54 mm)andless in thickness and 85 HRB for material over 0.100 in.inthickness when determined in accordance with Test MethodsE18.See also Test Method E92 for Vickers Hardness and Table3,E140 for the appropriate conversion between various hard-ness scales.8.2 Rolled and Annealed TempersHardness tests whenproperly applied can be indicat

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2