收藏 分享(赏)

ASTM_F_2863_-_11.pdf

上传人:益****师 文档编号:188942 上传时间:2023-03-04 格式:PDF 页数:2 大小:75.32KB
下载 相关 举报
ASTM_F_2863_-_11.pdf_第1页
第1页 / 共2页
ASTM_F_2863_-_11.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F286311An American National StandardStandard Specification forCentral Vacuum Hose Inlet Valve Socket Dimensions1This standard is issued under the fixed designation F2863;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the

2、 year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification establishes requirements and testmethods for dimensions and tolerances of central-vacuum hosein

3、let valve sockets.1.2 All notes and footnotes shall be considered as non-mandatory requirements of the specification.1.3 This specification does not apply to inlet valve back-up(or mounting)plates.1.4 This standard is applicable to universal valves markedwith ASTM F2863,and does not limit proprietar

4、y valvedesigns.1.5 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 This standard does not purport to address all of thesafety concerns

5、,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for Tes

6、tingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2749 Symbols for Dimensions of Plastic Pipe FittingsF412 Terminology Relating to Plastic Piping Systems3.Terminology3.1 Definitions are in accordance with

7、Terminology F412,abbreviations are in accordance with Terminology D1600,anddimension symbols are in accordance with SpecificationD2749.3.2 Definitions of Terms Specific to This Standard:3.2.1 central vacuum hose inlet valve,nI.D.controlledvalves used to connect vacuum hoses to the central vacuumtubi

8、ng systems.3.2.2 hose cuff,nend connector of a flexible centralvacuum hose that fits inside the socket of a central vacuumhose inlet valve.3.2.3 proprietary valve,nvalve with unique design spe-cific to manufacturers system specifications.3.2.4 unaided eye,nobservable without enhancement be-yond corr

9、ection for normal vision.3.2.5 universal valve,nValve meeting Fig.1 dimensionalspecifications.4.Significance and Use4.1 The requirements of this specification are intended toprovide inlet valve socket dimensions to establish standardiza-tion of connections between central vacuum hose cuff and thesoc

10、ket of the central vacuum hose inlet valve.5.Materials5.1 Basic MaterialsMetallic and non-metallic as specifiedby the central vacuum inlet valve purchaser and the seller.6.Requirements6.1 GeneralDimensions and Tolerances:6.1.1 Socket DimensionsThe socket dimensions shallmeet the requirements given i

11、n Fig.1,when measured inaccordance with Test Method D2122.7.Test Method7.1 SamplingThe selection of Hose Inlet Valve samplesshall be as agreed upon between the purchaser and seller.Incase of no prior agreement,samples selected by a testinglaboratory shall be deemed adequate.7.2 ConditioningFor time-

12、of-manufacture testing,condi-tioning shall be permitted at the ambient temperature and1This test method is under the jurisdiction ofASTM Committee F11 on VacuumCleaners and is the direct responsibility of Subcommittee F11.30 on Durability-Reliability.Current edition approved Nov.1,2011.Published Dec

13、ember 2011.DOI:10.1520/F2863-11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 B

14、arr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 humidity of the manufacturers facility.For non-metallic ref-eree purposes,conditioning shall be in accordance with proce-dure A of Practice D618.7.3 TestingTesting shall be in accordance with TestMethod D2122.8.Retest and Re

15、jection8.1 If the results of any test(s)do not meet the requirementsof this specification,the tests shall be conducted again inaccordance with an agreement between the purchaser and theseller.There shall be no agreement to lower the minimumrequirements of this specification by such means as omitting

16、tests that are a part of this specification,substituting ormodifying a test method,or by changing the specificationlimits.In retesting,the product requirements of this specifica-tion shall be met,and the test methods designated in thespecification shall be followed.If,upon retest,failure occurs,the quantity of product represented by the test(s)does not meetthe requirements of this specification.9.Quality Assurance9.1 When the product is marked with this designation,ASTM F2863,the manufacturer af

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2