1、Designation:F628121Standard Specification forAcrylonitrile-Butadiene-Styrene(ABS)Schedule 40 PlasticDrain,Waste,and Vent Pipe With a Cellular Core1This standard is issued under the fixed designation F628;the number immediately following the designation indicates the year of originaladoption or,in th
2、e case of revision,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.1NOTESections 2,6.4.4,and the Summary of Changes were editorially corrected in March 2013.1.Scope*1.1 Thi
3、s specification covers coextruded acrylonitrile-butadiene-styrene(ABS)plastic drain,waste,and vent pipemade to Schedule 40 iron pipe sizes(IPS)and produced by thecoextrusion process with concentric inner and outer solid ABSlayers and the core consisting of closed-cell cellular ABS.Plastic which does
4、 not meet the material requirements specifiedin Section 5 is excluded from single layer and all coextrudedlayers.1.2 Fittings suitable for use with pipe meeting the require-ments of this specification are given in Annex A1.Fittingsmeeting the requirement of Specification D2661 are alsoacceptable.1.3
5、 Acrylonitrile-butadiene-styrene plastic which does notmeet the definitions of virgin ABS plastic as given in 3.2.4 isexcluded,as performance of plastic other than those defined asvirgin was not determined.ABS rework plastic which meetsthe requirements of rework plastic as given in 5.3 is acceptable
6、.1.4 Reprocessed plastic or recycled plastic as defined inTerminology D883 is excluded.1.5 Recommendations for storage,joining,and installationare provided in Appendixes X1,X2,and X3,respectively.1.6 The text of this specification references notes,footnotes,and appendixes which provide explanatory m
7、aterial.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.7 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.2.Referenced Documents2.1 ASTM Standa
8、rds:2D618 Practice for Conditioning Plastics for TestingD883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1898 Practice for Sampling of Plastics(Withdrawn 1998)3D2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2235 Speci
9、fication for Solvent Cement for Acrylonitrile-Butadiene-Styrene(ABS)Plastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Para
10、llel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2661 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Schedule 40 Plastic Drain,Waste,and Vent Pipeand FittingsD3311 Specification for Drain,Waste,
11、and Vent(DWV)Plastic Fittings PatternsD3965 Classification System and Basis for Specifications forRigid Acrylonitrile-Butadiene-Styrene(ABS)Materialsfor Pipe and FittingsD5630 Test Method for Ash Content in PlasticsE105 Practice for Probability Sampling of MaterialsE1508 GuideforQuantitative Analysi
12、sbyEnergy-Dispersive Spectroscopy1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved Nov.15,2012.Published January 2013.Originallyapproved in 1979.Last previous edition ap
13、proved in 2008 as F628 08.DOI:10.1520/F0628-12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved
14、version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 E122 Practice for Calculating Sample Size to Estimate,WithSp
15、ecified Precision,the Average for a Characteristic of aLot or ProcessF402 Practice for Safe Handling of Solvent Cements,Primers,and Cleaners Used for Joining ThermoplasticPipe and FittingsF412 Terminology Relating to Plastic Piping SystemsF1498 Specification for Taper Pipe Threads 60 for Thermo-plas
16、tic Pipe and Fittings2.2 Federal Standard:Fed.Std.No.123 Marking for Shipment(Civil Agencies)42.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage43.Terminology3.1 Definitions:3.1.1 Definitions are in accordance with Terminology F412,and abbreviations are in accordance with Terminology D1600,unless otherwise specified.The abbreviation for acrylonitrile-butadiene-styrene plastic is ABS.3.1.2 cellular plastica plastic containing numerous cells,intentionally introduced,interconnecting
