1、Designation:F79403(Reapproved 2014)Standard Specification forPoly(Vinyl Chloride)(PVC)Profile Gravity Sewer Pipe andFittings Based on Controlled Inside Diameter1This standard is issued under the fixed designation F794;the number immediately following the designation indicates the year of originalado
2、ption or,in the case of revision,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scop
3、e1.1 This specification covers requirements for poly(vinylchloride)(PVC)profile sewer pipe and fittings with integralbell and elastomeric seal joints or plain end pipe with couplingsin sizes(4 to 48 in.)based on a controlled inside diameter.1.2 The values stated in inch-pound units are to be regarde
4、das standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following safety hazard caveat pertains only to thetest methods portion,Section 8,of this specification:Thisstandard does not purport to
5、address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.NOTE1Pipe and fittings produced to this specification sho
6、uld beinstalled in accordance with Practice D2321.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chlor
7、ide)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride)(PVC)Pipe and Molded Fittings byAcetone ImmersionD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers an
8、d Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2855 Practice for Making
9、Solvent-Cemented Joints withPoly(Vinyl Chloride)(PVC)Pipe and FittingsD3034 Specification for Type PSM Poly(Vinyl Chloride)(PVC)Sewer Pipe and FittingsD3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsF402 Practice for Safe Handling of Solvent Cements,Pr
10、imers,and Cleaners Used for Joining ThermoplasticPipe and FittingsF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic PipeF679 Specification for Poly(Vinyl Chloride)(PVC)Large-Diameter Plastic Gravity Sewer Pipe and Fittings2.2 Ame
11、rican Water Works Association(AWWA)Standard:AWWA Manual M45 Fiberglass Pipe Design32.3 Federal Standard:Fed.Std.No.123 Marking for Shipment(Civil Agencies)42.4 Military Standard:MIL-STD-129 Marking for Shipment and Storage43.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F
12、412,and abbreviations are in accordance with Termi-nology D1600,unless otherwise specified.The abbreviation forpoly(vinyl chloride)is(PVC).3.2 Definitions of Terms Specific to This Standard:1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct
13、 responsibility of Subcommittee F17.62 on Sewer.Current edition approved Aug.1,2014.Published November 2014.Originallyapproved in 1983.Last previous edition approved in 2009 as F794 03(2009).DOI:10.1520/F0794-03R14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Cus
14、tomer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Water Works Association(AWWA),6666 W.QuincyAve.,Denver,CO 80235,http:/www.awwa.org.4Available from Standardization Documents O
15、rder Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.2.1 dual wall corrugated profile(DWCP)gravity sewerpipea pipe product consisting of a sm
16、ooth waterway bracedcumferentially with an external corrugated wall(see Fig.1)3.2.2 open profile(OP)gravity sewer pipea pipe productconsisting of an essentially smooth waterway braced circum-ferentially or spirally with outside projections or ribs(see Fig.2).4.Significance and Use4.1 The requirements of this specification are intended toprovide pipe and fittings suitable for nonpressure drainage ofsewage and surface water.NOTE2Industrial waste disposal lines should be installed only withthe spec
