1、Designation:F270915Standard Test Method forDetermining a Measured Nameplate Recovery Rate ofStationary Oil Skimmer Systems1This standard is issued under the fixed designation F2709;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method defines a method and measurementcriteria to quantify the performance of a stationary skimmer inide
3、al conditions in support of a devices nameplate recoveryrate(capacity).If a determination of a skimmers capabilities inrealistic conditions(that is,advancing or waves)is required,testing should be performed according to Guide F631 orequivalent.1.2 This test method includes the option of testing tode
4、termine recovery efficiency.1.3 This test method and parameters are intended to provideideal recovery conditions allowing the skimmer system tooperate and collect oil at its maximum possible recovery rate.Given ideal conditions,inherent mechanical and physicalattributes of the system become the limi
5、ting factors.1.4 This test method is intended to identify limitations of theskimmer system,such as performance of the skimmingmechanism,the flow of oil within the skimmer and sump,thepump characteristics,and typical discharge head conditions.1.5 It is accepted that the measured nameplate recovery ra
6、teas determined by this test method will not likely be achievableunder actual conditions of a spill.The measured nameplaterecovery rate should be used in conjunction with a de-ratingfactor to account for such issues as changing encounter rate,changes in other recovery conditions,changes in oil prope
7、rtiesand slick thickness,number of daylight hours,operatordowntime,less than ideal control of skimmer settings,andinclement weather.1.6 This test method involves the use of specific test oilsthat may be considered hazardous materials.It is the respon-sibility of the user of this test method to procu
8、re and abide bynecessary permits and regulations for the use and disposal oftest oil.1.7 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.8 This standard does not purport to address all of thesafety concerns,if any,associated wi
9、th its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D971 Test Method for Interfacial Tension of Oil AgainstWater by the
10、Ring MethodD1298 Test Method for Density,Relative Density,or APIGravity of Crude Petroleum and Liquid Petroleum Prod-ucts by Hydrometer MethodD2983 Test Method for Low-Temperature Viscosity of Lu-bricants Measured by Brookfield ViscometerD4007 Test Method for Water and Sediment in Crude Oil bythe Ce
11、ntrifuge Method(Laboratory Procedure)F631 Guide for Collecting Skimmer Performance Data inControlled Environments3.Terminology3.1 Definitions:3.1.1 fluid recovery ratethe volume of fluid recovered bythe device per unit of time(m3/h).3.1.2 ideal conditionsoperating conditions that result inthe maximu
12、m nameplate recovery rate of a skimming systemwithin the limitations of the test method.3.1.3 measured nameplate recovery ratethe maximumrate at which the skimmer system can recover and process oilunder ideal conditions.3.1.4 nameplate recovery ratethe maximum skimmingcapacity of a device as stated
13、by the manufacturer.1This test method is under the jurisdiction of ASTM Committee F20 onHazardous Substances and Oil Spill Response and is the direct responsibility ofSubcommittee F20.12 on Removal.Current edition approved July 1,2015.Published November 2015.Originallyapproved in 2008.Last previous
14、edition approved in 2008 as F270908.DOI:10.1520/F2709-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright
15、 ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.5 oleophilicoil skimmers that use collection surfacesfor recovery,for example,disc,brush,drum,belt,mop,and soforth.3.1.6 oil recovery ratethe volume of oil recovered by thedevice per unit of time
16、(m3/h).3.1.7 recoveryeffciencytheratio,expressedasapercentage,of the volume of oil recovered to the total volumeof fluids recovered.3.1.8 skimmer systema skimmer and ancillary equipment,including power supply,hydraulic lines,discharge pump,suction/discharge hoses,and control apparatus.4.Significance and Use4.1 It has been industry practice to claim the capacity of askimmer based on the rate of the discharge pump(which aretypically rated using water as a test fluid)or other arbitrarymethods.4.2 E
