1、Designation:F283011(Reapproved 2017)An American National StandardStandard Specification forManufacture and Joining of Polyethylene(PE)Gas PressurePipe With a Peelable Polypropylene(PP)Outer Layer1This standard is issued under the fixed designation F2830;the number immediately following the designati
2、on indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This standard specification covers manufac
3、turing andjoining requirements for peelable(skinned)polyethylene(PE)pipe,which is PE pipe meeting the requirements of Specifica-tion D2513,with a peelable outer layer of polypropylene(PP).These requirements are in addition to those in SpecificationD2513 for the PE pipe.1.2 The peelable PP layer does
4、 not contribute to outsidediameter and wall thickness used for pressure rating or tensileloading calculations.1.3 The text of this standard references notes and footnoteswhich provide explanatory material.These notes and footnotes(excluding those in figures and tables)shall not be consideredas requi
5、rements of the standard.1.4 UnitsThe values stated in inch-pound units are to beregarded as standard.The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.5 This standard does not purport to address all of thes
6、afety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance
7、with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:
8、2D1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2513 Specification for Polyethylene(PE)Gas PressurePipe,Tubing,and FittingsD4101 Specification for Polypropylene Injection and Extru-sion MaterialsF412 Terminology Relating to Plastic Piping SystemsF1055 Specification for Electrofusion Ty
9、pe PolyethyleneFittings for Outside Diameter Controlled Polyethyleneand Crosslinked Polyethylene(PEX)Pipe and TubingF1563 Specification for Tools to Squeeze-off Polyethylene(PE)Gas Pipe or Tubing2.2 ISO Standard:3ISO 17454 Plastics piping systems-multilayer pipe-testmethod for the adhesion of the di
10、fferent layers using apulling rig.2.3 EN Standard:4EN 1411-Plastics piping and ducting systems Thermo-plastics pipes determination of resistance to externalblows by the staircase method.3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412,and abbreviations are in accordan
11、ce with Termi-nology D1600,unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.2.1 Peelable pipe,nSpecification D2513 polyethylene(PE)pipe coextruded with a peelable outer layer of polypro-pylene(PP).When the peelable PP layer is removed,the PEpipe is the same as D2513 PE
12、 pipe.4.PE Pipe and PP Layer Requirements4.1 PE Pipe Requirements:4.1.1 The PE pipe shall meet all the requirements ofSpecification D2513,excluding marking,when tested in accor-dance with 6.1.Marking shall be in accordance with Section 7.1This specification is under the jurisdiction of ASTM Committe
13、e F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.Current edition approved Aug.1,2017.Published September 2017.Originallyapproved in 2011.Last previous edition approved in 2011 as F283011.DOI:10.1520/F2830-11R17.2For referenced ASTM standards,visit the AST
14、M website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from International Organization for Standardization(ISO),1,ch.dela Voie-Creuse,Case postale 56,CH-1
15、211,Geneva 20,Switzerland,http:/www.iso.ch.4Available from European Committee for Standardization(CEN),36 rue deStassart,B-1050,Brussels,Belgium,http:/www.cenorm.be.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard
16、 was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.2 PP Layer Requirements:4.2.1 The PP peelable layer shall be made from unrein-forced PP material in accordance with Specification D4101.Any unreinforced PP material may be used as long as thepeelable pipe meet
