1、Designation:F292213(Reapproved 2018)Standard Specification forPolyethylene(PE)Corrugated Wall Stormwater CollectionChambers1This standard is issued under the fixed designation F2922;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、 year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers requirements,test methods,materials,and marking for polyethylene(PE),open bottom,buried
3、 arch-shaped chambers of corrugated wall constructionused for collection,detention,and retention of stormwaterrunoff.Applicationsincludecommercial,residential,agricultural,and highway drainage,including installation un-der parking lots and roadways.1.2 Chambers are produced in arch shapes with dimen
4、sionsbased on chamber rise,chamber span,and wall stiffness.Chambers are manufactured with integral feet that provide basesupport.Chambers may include perforations to enhance waterflow.Chambers must meet test requirements for arch stiffness,flattening,and accelerated weathering.1.3 Analysis and exper
5、ience have shown that the successfulperformance of this product depends upon the type and depthof bedding and backfill,and care in installation.This specifi-cation includes requirements for the manufacturer to providechamber installation instructions to the purchaser.1.4 The values stated in inch-po
6、und units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The following safety hazards caveat pertains only to thetest method portion,Section 6,of this specification:Thisst
7、andard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.6 This internati
8、onal standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committe
9、e.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2412 Test Method for Determination of External LoadingCharacteri
10、stics of Plastic Pipe by Parallel-Plate LoadingD2990 Test Methods for Tensile,Compressive,and FlexuralCreep and Creep-Rupture of PlasticsD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsD4329 Practice for Fluorescent Ultraviolet(UV)Lamp Ap-paratus Exposure of PlasticsD4703 P
11、ractice for Compression Molding ThermoplasticMaterials into Test Specimens,Plaques,or SheetsD6992 Test Method for Accelerated Tensile Creep andCreep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped IsothermalMethodF412 Terminology Relating to Plastic Piping
12、 SystemsF2136 Test Method for Notched,Constant Ligament-Stress(NCLS)Test to Determine Slow-Crack-Growth Resis-tance of HDPE Resins or HDPE Corrugated PipeF2787 Practice for Structural Design of Thermoplastic Cor-rugated Wall Stormwater Collection Chambers3.Terminology3.1 DefinitionsDefinitions used
13、in this specification are inaccordance with the definitions in Terminology F412,andabbreviations are in accordance with Terminology D1600,unless otherwise indicated.3.2 Definitions of Terms Specific to This Standard:1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping
14、 Systems and is the direct responsibility of Subcommittee F17.65 on LandDrainage.Current edition approved Feb.15,2018.Published March 2018.Originallyapproved in 2012.Last previous edition approved in 2013 as F2922-131.DOI:10.1520/F292213R18.2For referenced ASTM standards,visit the ASTM website,www.a
15、stm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C7
16、00,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2.1 chamberan arch-shaped structure manufactured ofthermoplastic with an open-bottom that is supported on feetand may be joined into r
