1、Designation:F40513Standard Specification forCorrugated Polyethylene(PE)Pipe and Fittings1This standard is issued under the fixed designation F405;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revision.Anumber in pa
2、rentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers requirements and test methodsfor materia
3、ls,marking dimensions,workmanship,elongation,brittleness,pipe stiffness,and perforations for corrugatedpolyethylene(PE)pipe and fittings in nominal sizes of 3 to 6in.,inclusive.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalcon
4、versions to SI units that are provided for information onlyand are not considered standard.NOTE1Along with sizes 3 to 6 in.covered in this specification,sizes4 to 24 in.are described in Specification F667.1.3 The text of this specification references notes andfootnotes that provide explanatory mater
5、ial.These notes andfootnotes(excluding those in tables and figures)shall not beconsidered as requirements of the specification.1.4 The following precautionary caveat pertains only to thetest methods portion,Section 8,of this specification:Thisstandard does not purport to address all of the safety co
6、ncerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for
7、 TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD3350 Specification for Polyethylene Pla
8、stics Pipe and Fit-tings MaterialsF412 Terminology Relating to Plastic Piping SystemsF667 Specification for 3 through 24 in.Corrugated Polyeth-ylene Pipe and Fittings3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412,and abbreviations are in accordance with Termi-nology
9、 D1600,unless otherwise specified.The abbreviation forpolyethylene is PE.3.2 Definitions of Terms Specific to This Standard:3.2.1 crackany break or split that extends through thewall.3.2.2 creasea deformation that cannot be removed like adent;generally associated with wall buckling.4.Significance an
10、d Use4.1 Corrugated PE pipe and fittings are intended for under-ground applications where soil support is given to the flexiblewalls.Their major uses are in soil drainage and septic fieldleach beds(see appendix for installation guidelines).4.2 Corrugated fittings complying with the requirements ofth
11、is specification may be used with either standard or heavy-duty pipe as defined by the requirements of Table 1.5.Materials5.1 GeneralCompounds used in the manufacture of cor-rugated PE drainage pipe and fittings shall have a minimumcell classification of 323410C or 333410C as defined anddescribed in
12、 Specification D3350.Compounds that have ahigher cell classification in one or more properties areacceptable,provided the product requirements are met.NOTE2Class B pigments may be substituted for Class C provided thatultraviolet protection is acceptable to the purchaser as satisfactory for theintend
13、ed use.5.2 Rework MaterialThe manufacturer shall use only hisown clean pipe or fitting rework material;the pipe and fittingsproduced shall meet all the requirements of this specification.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct re
14、sponsibility of Subcommittee F17.65 on LandDrainage.Current edition approved Aug.1,2013.Published August 2013.Originallyapproved in 1974.Last previous edition approved in 2005 as F405 05.DOI:10.1520/F0405-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer S
15、ervice at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-295
16、9.United States1 6.Requirements6.1 The pipe and fittings shall be homogeneous throughoutand free of foreign inclusions or visible defects.The pipe andfittings shall be as uniform as commercially practicable incolor,opacity,density,and other physical properties.The endsshall be cut squarely and cleanly.They shall be free of internalobstructions,including defective seams or mold registrationlines.The product function shall be considered when judgingexternal defects.6.1.1 Visible DefectsCracks,crea
